Recent content by cash84

  1. C

    Car bogging down

    I've had that happen! It was worst than bogging! It acts like the engine has no power at all. Glad it got fix under warranty but like a month afterwards I got rid of it by just putting mopar race exhaust. Now I don't have to worry lol
  2. C

    Hosting a meet July 21st

    You gotta make it! It's been like over two years since we last seen each other lol. Ur slacking! Haha kiddin. Hope to see ya there
  3. C

    Car bogging down

    I've had a bogging issues about an year and half ago when it was mostly stock with exhaust intake and tune. Turns out that when I put new plugs and wires in, it went away. I used the new AB wires and the stock champion plugs. How many miles on the car?
  4. C

    Didn't even had a chance to complete two laps at a HPDE event.

    No, you have not told me. I have to disagree with you. These pumps are junk. I already went through one and another viper owner I know went through two, on top of how many been replaced I've seen on here. These are suppose to help keep our engine cool, once they fail are are screwed if its a...
  5. C

    Didn't even had a chance to complete two laps at a HPDE event.

    It's not much of a hassle just the fittings to get to run a -6AN Teflon hose, PITA! no fittings I could find. I had to turn one fitting to make it seal on the rack and well a -6AN on the pump fitting then its all good. Get an 08+ fan and an dual control module to run both fans. The secondary...
  6. C

    Didn't even had a chance to complete two laps at a HPDE event.

    I went to a HPDE event today and it rained the first two session. Finally cleared up and got all ready for the third session. I did a build on the engine since last year from engine starvation. Forged internal, cam, etc. After the first lap of warm up and as soon as I started to get into it more...
  7. C

    Spin Control School

    I believe this 100%!! I saved my a$$ quite a few times by using the throttle. Easy answer. When the car gets out of control the normal brain reaction is to lift off the throttle. Weight transfers more to the front wheels which are now pointed in the direction of the slide. Hence you exit the...
  8. C

    Watch out for the new E15 gasoline.

    I have a friend that runs on E85 in his mits. EVO and creates a lot more power over straight gas. Down side Horrible cold start Smells funny (not bad but not good) Way worst milage (used to get like 30mpg and now maybe 21-22mpg) Prices are getting close to what straight gas cost It's a joke...
  9. C

    wraped rotor? ACR

    Another suggesting, did you switch pads on the same rotors? this can happen. I figured this out the hard way.
  10. C

    Dry sump

    Doesn't create vacuum.... there are so many different advantage over that compare to a swing arm. One is also that having a tank seperate from the engine keeps oil temps way down. In fact, I have a heater installed to help warm up faster. Average temp I seen on my oil was around 180-190 which is...
  11. C

    Could not get into my 03 Viper, Anyone else ever experiance this

    Agree, the key is like a door handle. Once the key is turned, it will pop the door open. I thought I was gonna snap my key but it didn't.
  12. C

    First meeting

    Will be there tomorrow :) No cruise in the viper tho. Still working on my dry sump system.
  13. C

    WTB: Gen 3 crank damper, pulley, bolt

    Thanks for the picture! I'm trying every effort not to remove the A/C. Where were you able to put the oil Tank? Best solution I found was right in front of the engine. I am switching to a Gen 4 rad fans to gain little room. Opps, I misread what you said but yes I know what you mean by turning...
  14. C

    WTB: Gen 3 crank damper, pulley, bolt

    Thanks for the catch! Okay, I can turn the seal around. The hub just catches the seal. My other option is to mill down the the hole for the seal to gain some room but turning the seal should be good. It's about .06 I need to gain. Do you know my any chance if someone may have a gilmer pulley...
  15. C

    WTB: Gen 3 crank damper, pulley, bolt

    Well I got the gen 4 damper. One problem, it sits tight against the seal so I found a exact size washer 18ga and it got enough to space out away from the seal. I now see that it's going to be a pita to route a belt to the location I plan on having the pump. I just need a day break on this. I...

Members online

Forum statistics

Threads
153,139
Posts
1,681,565
Members
17,640
Latest member
SDViper
Top