Yeah... I keep breaking cranks. Billet crank is on order and so that and a Turbo 400 will go back in it whenever the crank is ready.
ARD is good people. Top notch shop.
Yup. The stockers break w/o any power mods. try SEARCH and you'll see all the carnage. Baby the cars and you get lucky. Even Plum didn't dump the clutch on NOS on the street. But launch hard once and kiss those shafts buh-bye.
Actually, the main thing you need is half-shafts. A friend of mine skipped them and snapped the stock shafts first time out. They are weak on a stock car and wheel-hop will destroy them. spend the extra money and do it else you'll be whining here for a set of used ones or paying full...
When the reverse lockout is grounded, you can engage R. When it isn't (as in when the car is off), you can't. I've actually had a case of needing to manually wire the ground due to the exact opposite problem: NOT being able to engage reverse. I'd check the harness and clean it out...
They all say that. I did some research before I bought the RSI clutch... they have an exclusive agreement w/ the manufacturer. The support has been stellar and the clutch has handled my 1500rwhp+ beautifully.
I wouldn't be surprised if BBG ended up in a lawsuit over it... just sayin'...
So to clarify, what is the difference between your clutch and the RPS clutch assembly which is exclusively licensed to RSI? As one of the first users of the Gen II prototype (including helping RPS figure out how to make ti work with a gen2 flywheel), it would be helpful for me as well as the...
Yes, the T-stat housings are different. But that doesn't matter. What matters is that some coolant from the block gets back to the heater core. If you don't have the nipple, just connect a 90 deg from the back of the pass side head that has a plug in it and take the coolant out of there...
The PS pulley is 'pressed' on. I'll bet you have some clearance to press it back ever-so-slightly.
Let's not forget, the cars were hand built. I've seen tight tolerances on the 10-rib set-up before. Before you do what I'm about to suggest, check your paxton pulley alignment... if it is...
Looks awesome! And great move!
No disrespect, but for the rest of y'all considering this: Autozone has 18" length of 3" pipe for like 6 bucks. that plus a sawsall + 2 clamps and you are done in less than 3 hrs per side. 6 hrs total... that's a long day.
rock on! :headbang:
It bothers me that people post the same question on multiple forums. :rolaugh:
I'm not sure who gave the idea that a paxton needs to be rebuilt every 10k miles. The smartest thing to do would be to call Paxton and ask them rather than speculating. They will give you the MTBF (mean time...
You'd have run about 134-136mph... So I'm guessing a new driving will drive 11.5 first times out. Only 9psi and 750hp, you won't hit 139mph unless you spin badly. But then your et suffers.
With the heat coming, none of us will break any records until it cools off...
What 'revision' does it say you have on the back of the AEM? There had been at least 3 recalls on the AEM, including one where exactly what you are describing happened.
I have had some very positive experiences with Palmer as of late. In fact, I recently bought my new daily driver from Jared. He made it remarkably easy to buy and I would concur that they have turned over a new leaf. And it is a good one! :headbang:
Joseph
Most 2003 trannys did NOT have the provision for the speed sensor. But in order to make warranty replacement easier, 2004-2006 T56's have the provision for the speed sensor. If you have a 2003, you can see where you'd need to drill (and add a tone ring inside the tranny) to make it compatible...
Thursday my car would go into reverse. Friday it wouldn't. Turned out tube loose connection on the reverse lock-out wiring harness that goes to the tranny. 90 minutes with a multimeter, some dialectic grease, and a paperclip and I was working again. In retrospect, 5 min and a paperclip would...
That is because AEM isn't emissions legal. get a stock computer w/ an SCT tune or the mopar performance ECU and you'll have a better shot at passing.
good luck!
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.