Search results

  1. M

    1994 (Gen-1) A/C o-rings

    I'd also suggest swapping-checking the o-rings at the condenser on the driver's side where the link connects. Both my 200 GTS & '96 RT/10 needed those changed. Not a bad job either, if you remove the panel between the fascia and air filter box...
  2. M

    AC needs recharging every year?

    In both my '96 RT & 2000 GTS.....the worst A/C leak was where the line connects to the condenser. On the drivers side, the line comes down into the compressor. You can see it looking though the bumper. I replaced the o ring by removing the air filter box, and the panel in front.
  3. M

    How thick is Viper (Dodge) Clearcoat?

    The real problem is that you haven no idea how many times its been polished since new.. I'd only suggest working a lightlyas possible. Agreed, on the finger nail test.
  4. M

    1996 OEM Battery Needed

    Frank...count your blessings that Interstates are hard to get near you. My Lincoln just had it's 2nd Interstate fail in less than 24 months, each. My local shop stopped selling them and switched to Deka.
  5. M

    Hey why has no one done this to an RT/10!

    The obvious reason? Besides how horrible it would look? No room. The gas tank is where your rear footwell would have to be. That AMX as concept car that never made it to production.
  6. M

    1996 OEM Battery Needed

    Hi Frank....the batteries installed at the factory aren't available. The battery went in my 1996 when it was a couple years old and the only replacements from Chrysler were generic Mopar batteries. Nobody reproduces an exact replacement, either. Those of us with early Vipers are stuck in a spot...
  7. M

    Fuel Pump DIY?

    I looked up my print-out of this from when I did it on my '96 RT. These are the ones "ticked" on my instructions... 1. Power supplied with key-on (zero volts when key-off, 12V when key-on) a. In a Gen 1, connect red wire to A21 14DB (dark blue) 2. Ground by PCM to complete the circuit...
  8. M

    Fuel Pump DIY?

    Photopro...the wiring instructions are on that link...the same I used for my '96 RT
  9. M

    ramps for scissor lift

    Thanks Don....it was really simple to make...and cheap. 2x3s are very inexpensive. If you use 2x12s (which won't give you as much height as my ramps) I'd suggest pressure treated....which aren't cheap.
  10. M

    ramps for scissor lift

    I too have a mid-rise lift in my middle bay. I used to clear it with the Vipers with a pair of 2x12s. However, I made something up a bit better with a bunch of 2x3s. Since the picture was taken, I added some metal corners at the closer ends where the tires go up the ramps. This helps keep the...
  11. M

    Front Fascia Installation

    Replace ALL the fasteners and you won't have the big gap at the headlights.
  12. M

    Question about my ventilation ???

    These Vipers use a vacuum "switch" to control where the air condtioned air goes. If vacuum is gone, the "default" position is the defroster vents. (This also can happen momentarily if the gas pedal is pressed down very far in a higher gear.) The A/C air coming from the defrost vents has NOTHING...
  13. M

    Front Fascia Install

    Most don't put the fasteners back in under the headlights and when it's hot....you get the gaps. There is really no (or very little) adjustment. In my opinion...it's important to put all fasteners back or you'll have gaps. If memory serves, we used a bolt and nut in the under the headlight...
  14. M

    Dealer says he knows the car.

    Frank....don't know what you're looking for.....but....a local club mate of mine is looking to sell a '93 with 9000 miles. Under the fascia is scraped a bit...needs tires from dry rot...dash paint is spent (no surprise). I've never studied the car...but if you want to know more....PM me..
  15. M

    Engine Start

    There is a mod done by Tom (the oil guy) for a simple timer that was an easy install. It allows the fuel pump to run longer when the key is first turned on...but maintains the safety feature of shutting down in the event of a problem. So...when you first start the car you just leave the key in...
  16. M

    Engine Start

    It's true the fuel pump will only run for one second when the key is turned on. So...turn it on and off several times...then try to start the car. It may take 5 or more "on and offs" with the key...but you'll know if the problem is that pressure valve. (I call it a pressure valve...but that may...
  17. M

    How to reinstall the front fascia

    Dom....the push fastener under the headlights is the one I replaced with a nit and bolt. I don't have any pictures either, but I do remember many Vipers are Carlisle that had the "gap" where that fastener was missing. I mentioned it to my wife who remembered the ordeal that led to the nut/bolt...
  18. M

    How to reinstall the front fascia

    Titlemine...they aren't Chrysler specific clips. I got a whole box made by W&E. Any good auto body supply shop should be able to get them for you...just take a sample with you.
  19. M

    How to reinstall the front fascia

    When I pulled-replaced the fascia on my RT I was amazed at how many folks had written that there are clip you "don't need to put back". I think this explains why some Vipers get gaps around the headlights…especially the heat. There are a couple very near or under the headlights that were tough...
  20. M

    Please help with air conditioning

    Again....even if the compressor is disengaged at full throttle..it's not going to result in hot air immediately at the vents. The compressor cycles on and off all the time....the evaporator won't get hot immediately.
  21. M

    Please help with air conditioning

    I can't imagine how the evaporator could immediately go from cold to hot when the gas pedal is depressed. I can see how a vacuum leak could cause the blend door to move and perhaps direct more warm air into the mixture. If the compressor clutch was somehow set to disengage...I can't see...
  22. M

    Please help with air conditioning

    I never heard that the A/C shuts off when you apply the gas…. I do know that the HVAC will direct the conditioned air from the dash vents to the defroster vents if vacuum is lost. (I've only noticed this in 5th or 6th gears on the highway when the gas pedal is pressed far down) There's a check...
  23. M

    Convince Me! Gen I vs Gen II

    The OP shows a Gen 1 with a repaint, and aftermarket "upgrades" vs a clean Gen 2 apparently with no stories. In my book...you're far better off buying a better car upfront. In this case, the 01 is the better choice of the two. That being said, I prefer the Gen 1 RT over the Gen 2. All a matter...
  24. M

    94 battery replacement

    Yes, the battery is behind the drivers side wheel. Remove the wheel, a few bolts...a couple plastic fasteners and pull the inner fender lower portion. As said before....it is important that the battery terminals don't touch the frame rails. Also...the battery isn't there for weight...
  25. M

    Fuel Pump DIY?

    I too would be interested in a replacement pump. I do agree with CS14...it could be a standard replacement...

Latest posts

Members online

Total: 882 (members: 13, guests: 869)

Forum statistics

Threads
153,192
Posts
1,681,861
Members
17,686
Latest member
Javadog62

Share this page

Top