Search results

  1. R

    '04 Shifter Detent/Centering

    Got to agree 100%. Every shifter i have installed I have done from under the car on a lift.
  2. R

    Battery Tender

    Still have the original battery in my 2003 viper and it has never let me down. It gets down below zero here in CT, and it starts up fine. What you need to do is wire in a battery tender. I installed mine on the shelf in front of the brake master cylinder and wired it to the hot post on the...
  3. R

    Wheel Hop

    I replaced the motor and transmission mounts with Woodhouse/Snake-Oyl mounts, mounted Michelin NON Run Flat PS2 tires and the wheel hop was eliminated.
  4. R

    Absorbed Glass Matte Battery

    Still have the original battery in my 2003 viper and it has never let me down. It gets down below zero here in CT, and it starts up fine. What you need to do is wire in a battery tender. I installed mine on the shelf in front of the brake master cylinder and wired it to the hot post on the...
  5. R

    Correct tire pressure to run?

    We run 34 Front and 30 rear with Michelin PS2 tires, this takes out some of the push or under steer that is dialed in at the factory stock setting of 28 psi.
  6. R

    Will the JET-61610 skip-shift eliminator work for the SRT coupe?

  7. R

    Warrenty Question

    I have a 2003 that I bought brand new and it came with a 7-70 powertrain warranty. The rear diff is part of the powertrain. The question here is simple. Did Alan have the 7-70 powertrain warranty transfered to his name when he bought the used 2003 viper? If so it is covered. If not then he needs...
  8. R

    H/F cat install question

    Got to agree with "VicTxV10" above. We have never had to replace the clamps with new ones. just be careful and take your time. They will come off and they can be reused.
  9. R

    Will the JET-61610 skip-shift eliminator work for the SRT coupe?

    Yes the 60610 will fit. So will Hurst Part# 155-0100 C.A.G.S.SKIP SHIFT KIT. Solenoid is on the driver side and you will have to remove the belly pan which takes less than 5 minutes. Total time for the job is 15 minutes on a lift. :drive:
  10. R

    Gen III Intake manifold removal

    That's Mopar for you!
  11. R

    Mysterious Black Smoke

    IMHO Vipers are not made for drag racing. They are road racing cars. Road racing cars do not drag race. Case in point here: have you ever seen a SCCA Trans-AM race car car drag race at a road racing circuit? If you want to drag race buy a Mustang or a Dodge SRT-10 Challenger. As I stated above...
  12. R

    Gen III Intake manifold removal

    You can reuse the intake manifold gaskets if you like, but considering the time it takes to R & R the intake manifold, I would replace them. Here is the part number from Mopar. 5037-217AC INTAKE MANIFOLD GASKETS, Qty 2 needed
  13. R

    H/F cat install question

    If you Adjust Rear Edge Of Exhaust Tip, 64' Cold & 64-1/2" Hot, from the Metal Wheel Inner Fender Support By Front Cat you will be pretty close.:2tu:
  14. R

    air filter on 08

    This seems to be the problem with the new 2008 ECM Emissions standards. My 2008 Miata did just this when I installed a K & N Filtercharger Kit. It ran like crap and threw a code. I replaced the kit with a K & N replacement filter, reset the ECM, and all was well.
  15. R

    Pulled over for race car on street

    Yes, here in Connecticut on I-95. Told me I accelerated to fast and wrote me a $400.00 ticket. Judge threw it out as there was no written police report on file.
  16. R

    New Car Mileage Question?

    My 2003 had 4 miles on it when I looked at it on the dealers showroom floor.
  17. R

    Rattling noise from the center of the dashboard? Need your help.

    I do believe AllData is screwing with me on this one. I do have a subscription but whenever I post here the pictures only work once for some reason. If needed shoot me an email and I will copy and paste the above instructions into an email.
  18. R

    air filter on 08

  19. R

    2008 Parts Manual

    The 2008 IS LISTED at the link below. I looked up a 2008 viper before I posted it. You need to click on the blue links on the left side of the page and then do the same under the sub categories in the right pane. Then click on the "View Illustration" tab. Mopar Parts for Dodge, Chrysler and...
  20. R

    Initial estimate for damage

    Give Jon at Parts Rack a call as he may have some used parts available. http://partsrack.blastmart.com/customer/home.php Also check here: http://www.x2builders.com/default.asp
  21. R

    Rattling noise from the center of the dashboard? Need your help.

    1.Remove the defroster grille from IP (using trim stick or equivalent). 2.Remove the defroster duct mounting screws (2) and defroster duct (Fig. 1). 3.Using snips/cutters, remove upstanding flange around entire outlet side of duct (Fig. 1). 4.Remove any loose debris from the defroster duct...
  22. R

    Maxcare from local dealer for 1800/0 dedctbl

    Hey Chuck, You are still the best and thats for the help last week. As always anytime I have called Chuck for help he has dropped everything and spend all the time needed to discuss my problem. PS: By the way Chuck, the new Cam Sensor had a vertical "Boss" molded onto the end of it that...
  23. R

    08 ECU Re-Learning

    After the screw up with the Filter Charger from K & N I went out and installed just a replacement filter, by K & N, in the stock air box. It did not mess up the ECM but I did not see any real gain over the stock OEM filter. Then I installed a Goodwin Racing full exhaust system including cats and...
  24. R

    NEW MEMBER

    Glad to see you here. Enjoy your new ride!
  25. R

    Gen IV ACR vs. Non-ACR

    I know this is a little off the subject but if anyone wants the ACR Owners Manual I have it in PDF format and can email it to you. If you want it then email me at [email protected] and I will send it to you as an attachment. No PM's please.

Latest posts

Members online

Total: 489 (members: 9, guests: 480)

Forum statistics

Threads
153,184
Posts
1,681,830
Members
17,683
Latest member
Dsalameh

Share this page

Top