Search results

  1. G

    WTB 2005 hydrolic fan. I think mine is gone :(

    If you unplug the water temp sensor wire at the thermostat housing the fan should run on high speed if everything is working right.
  2. G

    Hardwire Escort Into Mirror?

    Mine has worked fine now for 4 years. Comes on when you open the door and goes off after 15 minutes of inactivity.
  3. G

    Hardwire Escort Into Mirror?

    The BCM will cut the power to the mirror in 15 minutes if there is no activity. Even with the doors open.
  4. G

    VCA Raffle

    Been there a few times...might have to get out more!
  5. G

    VCA Raffle

    There's always next time!
  6. G

    VCA Raffle

    Hey Andy, He did tell me you stopped by but I was out of the office. We need to get together some time and tear up the roads! I bought 9 tickets for the raffle and want to know if I won the car?:dunno:
  7. G

    VCA Raffle

    Who won the car this morning??????
  8. G

    VCA Raffle

    Anyone know where I can pick my car up?:lmao:
  9. G

    supercharger was it a mistake

    Your right Mark.....I hate the the one you put on my wife's car....I can barley beat her in my 08 with the headers and PCM now:lmao::lmao: Oh yeah.....the maintenance is terrible, I had to change the oil for the second time now in 6000 miles:dunno: Seriously if you can't afford it don't do...
  10. G

    Corsa Exhaust CEL Issue

    Check and make sure the wires to the 02 sensors are good and if so reset the code with a scan tool and see if it comes back. Mine did it only once.
  11. G

    Torque Spec help please

    Your welcome.....anytime!
  12. G

    Torque Spec help please

    For the caliper bolts. 2. Install brake caliper (40 on steering knuckle (1). Install brake caliper mounting bolts and tighten to 115 N·m (85 ft. lbs.). 3. Install brake flex hose on brake caliper as follows: a. Place NEW copper seal washers on each side of banjo fitting located on...
  13. G

    Torque Spec help please

    This is from the service manual...hope it helps CAUTION: A special corrosion prevention gasket (1) must be installed between the hub and bearing and the steering knuckle. The gasket is required to prevent galvanic corrosion between the hub and bearing and the steering knuckle. 1...
  14. G

    Texas Mile

    Tim, Nice meeting you also. That's one nice car you have. I love the Roe blowers just wish they made one for my car. Let me know if your going to be in Texas again and we'll hook up for some more Viper action!
  15. G

    Texas Mile

    Just got back from Goliad and still can't believe how much fun that was! Got to see Art run 240 mph and two 239 mph passes. The best we did in my 2008 was 176.8...not bad for a street car! Lots of really nice fast cars there. Anybody else there over the weekend?
  16. G

    Gen 4 FULL Belanger set up. Opinions?

    FYI- it took 200 miles for mine to pass after I put the stock PCM back in. I'm in Galveston County
  17. G

    Gen 4 FULL Belanger set up. Opinions?

    I have this set up on my 08 and although the CEL is not on when they plug the state computer into it is says "Not Ready". I just put the stock PCM back in the car and drive it about 200 miles and then it passes.
  18. G

    Air/Heater Box?

    A/C drain?
  19. G

    Texas Mile

    I'll be there with my 08 Venom Red coupe. We are going to trailer it down behind the motor home. Looking forward to meeting everyone. Gary
  20. G

    Texas Mile

    I got my spot at the Texas mile March 25-27 anybody else going to be there?
  21. G

    2012 Dodge Viper

    Really.........it was just printed yesterday? Marchionne shows 2012 Dodge Viper at dealer meeting — Autoblog
  22. G

    2012 Dodge Viper

    I saw this on AutoBlog this morning! At yesterday's Chrysler dealer conference, the Pentastar people publicly revealed new or updated products from Chrysler, Dodge, Jeep and Fiat. But there was more on stage than just a facelifted Town & Country and a federalized Fiat 500. Towards the...
  23. G

    Smog Test Results on Gen IV with ACRX track headers

    I tried it here in Texas with the Mopar PCM and it would not pass. It said "not ready". Then when I put my stock PCM back in I had to run it for about 200 miles to get it to pass. They use the OBD II plug to read it. The engine makes a bunch of popping noises in the pipes with headers and the...
  24. G

    The First Raffle of 2010 is Now OPEN!!

    Wasn't the drawing yesterday??? Who won?:dunno:
  25. G

    Oil Pressure on 03 Viper

    From the service manual: (6) Inspect oil pressure relief valve for scoring and free operation in its bore. Small marks may be removed with 400 grit wet or dry sandpaper. (7) The relief valve spring has a free length of approximately 68.7 mm (2.70 in.) and should test between 22.5 and...

Latest posts

Members online

Total: 822 (members: 10, guests: 812)

Forum statistics

Threads
153,197
Posts
1,681,910
Members
17,696
Latest member
sloth

Share this page

Top