Search results

  1. 2

    My new to me 2000 GTS and Thanks to A&C

    Man that car makes a lot of power but do you think it needs a cam that big. That's a huge duration! How is the tq curve? Does this mean I can get a ride this weekend?
  2. 2

    Any one selling a nitrous kit?

    I've been looking at all the brands and just want to see if someone might have a kit that they don't have a use for
  3. 2

    Nitrous gurus need your advice

    I'm looking to added a small nitrous shot to my h/c viper. I have a few questions. I should be in the 550rwhp+ range and want to add a 100 shot nothing to big. I found a pretty good deal on a dry kit and was wondering if that would be safe for what I'm doing. Also being a h/c car with a stock...
  4. 2

    dropped price on tires and wheels

    I had to let mine go for 1000
  5. 2

    Bigger injectors with heads and cam?

    Do you know the flow rate? Where they increased all at?
  6. 2

    Bigger injectors with heads and cam?

    Well that's what I'm shooting for. Thank you Dan I won't waste any money on them
  7. 2

    Bigger injectors with heads and cam?

    I've search this topic quit a bit but still no solid answer. I'm going Greg good heads and cam build, from what I've read some get away with stock injectors but there about maxed out. I've found that the 300zx side feeds are 370cc and will drop right in. That is a 35lb injector vs a stock...
  8. 2

    2000+ Supercharger Question

    If you can do a TT setup for the same cost then that a no brainer. But for 10k I would find a used s/c setup with a head and cam
  9. 2

    Bent valve?

    I wouldnt worry about that piston at all. If its just a little scratch like you said your good to go
  10. 2

    Bent valve?

    I Bought a set off heads that had a dropped seat. I sent them to be ported and bigger valves so all the seats had to be removed with bigger seats installed. It is from the different expansion rates of the metals. The only real way to fell better about the head is to have the seats replaced or...
  11. 2

    Bent valve?

    Thanks for that dirtysocks!
  12. 2

    Trying to figure out wheel offset. Can you check my math

    Well I’ve ran the number for about an hour to make sure this is right and here is what I have gotten Stock wheel back spacing 18x10 front 2"=50mm offset 18x13 rear 2.5"=63mm offset Now minus the spacer width that people are running to make the stock wheels flush which takes away from...
  13. 2

    Mobil 1 oil filter vs Mopar Viper spec

    What is this part number for this filter? I have always just grab the mopar filter on the self at orileys
  14. 2

    Need A Harmonic balancer and Piston rings

    Yes sir I sent you a PM
  15. 2

    Need A Harmonic balancer and Piston rings

    Well as I get closer to warping up my build I still need a few things.. I broke the harmonic balancer when trying to take it off so I need a replacement. Ill take a stocker or aftermarket just let me know what you have.. im also putting in a set of 98 pistons in her and have the bearing Im just...
  16. 2

    Swapping pistons do I need to balance my rotating assembly?

    Well I decided why my heads where off to try and put in some OEM 96-99 forged rods and pistons. I drawl the line at dropping the tranny and the crank to get everything balanced. I was hopping that the weight of the 02 pistons would be close enough with the 99 that I could get away with it.. Any...
  17. 2

    how hard/expensive to change Connolly interior to black?

    Pm me I have a black interior and I would be interested in a stright swap
  18. 2

    Bellinger Header gaskets

    I'm running mr. Gasket graphite gaskets they where 20 bucks from summit and are great gaskets
  19. 2

    Big thanks to Tator's Garage

    I want to thank Tator for a big help putting together all the gaskets I need for my head and cam swap and giving me a super deal on them!! Thanks again!
  20. 2

    Incredible results from Heads & Cam build in Ohio

    What where all done to The heads what where the flow numbers?
  21. 2

    OK Guys, Do I HAVE to put 500 miles on them!

    When unitrax put my 3:73 in they said I could give it a little gas every once and awhile just not a full blown rowing through the gears... But after 2 heat cycles and 300 or more miles you will be fine
  22. 2

    Car back from A&C Performance

    Did you paint the valve covers and intake or did you have someone do it?
  23. 2

    Need help with my budget head and cam build

    This has been about 12 months in the making. I've been slowly taking my time and searching for good used part to put together my build. I'm in the military and have a wife so I can't drop 5 grand at once with all the bells and whistles lol. Anyways Mr. Good said my heads would be done soon so...
  24. 2

    What is a set of heads worth?

    I was thinks off selling my stock arrow rebuild heads off my 02 gts to finance the rest off my head and cam swap. How much is a set of heads with about 2500 miles on them worth?
  25. 2

    -FROG-'s Viper GTS Paxton Supercharger project pics.

    Looks great when are you sending it off to the dyno to get tuned?

Latest posts

Members online

Total: 662 (members: 7, guests: 655)

Forum statistics

Threads
153,189
Posts
1,681,844
Members
17,684
Latest member
Liberty235

Share this page

Top