2easy
Enthusiast
Xviper builds them for half the price and I think Vipair does as well but I am uncertain what he charges.
Gen 3 - Gen 4 hood swap
- Thread starter rvansnick
- Start date
Xviper builds them for half the price and I think Vipair does as well but I am uncertain what he charges.
Good to know!
Green viper 1
Enthusiast
- Joined
- Jun 3, 2012
- Posts
- 358
- Reaction score
- 0
there is a full set on eBay for 274
Viper Parts of America
Enthusiast
- Joined
- Feb 16, 2010
- Posts
- 597
- Reaction score
- 1
Don't forget that you then need the 42 push pins to attach them - which list at $4.20 each. We sell the pins for a $1 a pop or include them for free with brand new Mopar screens:
https://www.viperpartsofamerica.com/index.php/products/2008-2010-dodge-viper-srt10-hood-screen-set
https://www.viperpartsofamerica.com/index.php/products/2008-2010-dodge-viper-srt10-hood-screen-set
Green viper 1
Enthusiast
- Joined
- Jun 3, 2012
- Posts
- 358
- Reaction score
- 0
If it is what I think it is its wire lathe from Home Depot it's made for stucco but it is only like 5 dollars a sheet just have to paint it matte black
Exactly what I'm talking about!
Keep us informed
Mamba52
Enthusiast
Love your car!!! . It's a shame that you need a plate on the front. I will be up your way this summer (Mississauga) with my snake. We should get together.
ROYMAN
Enthusiast
In regards to the airbox sealing/not sealing... I put the VIPAIR hood on my 04, complete with the grills and the hood liner. Heat has not worked properly since. I was thinking the engine was too ventilated? Maybe its something else. Anyone else run into this problem?
Sonoman
Enthusiast
The heater system works off a small heat exchanger ("heater core") located under the right side of the dash. Hot water from the engine's cooling system gets routed through that heater core. If your heater is not working properly, the common issue would be a flapper door which channels incoming air through the heater core when heating is selected by the dash controls. In some cases (and I have not worked on my Viper for this specific problem, just other cars) the flapper is controlled by engine vacuum and a disconnected vacuum hose can cause the problem. But I believe the Viper has electric solenoid operated flapper doors. In any event, the type of hood would not/should not affect the operation of the heater.
In Gen3's, you do get some residual heating from the underhood air leaving the passenger side hood vents and then entering the fresh air intake at the base of the windshield. One advantage of the Gen4 hood design is that this transfer of underhood air is minimized by moving the vents forward. On a stock Gen3 with ventilation turned on and no heat requested, the incoming "fresh air" isn't all that cool, and you also get some preheated air (from the hood vents) coming in around the windshield with the top down.
ROYMAN
Enthusiast
Thanks for the advice! its still very cold here in MA but once I get the car back on the road I will make sure to check it out.
JAY
Enthusiast
Thanx Mamba52 ! Sounds good , give me a heads up ahead of time , in case I'm up at the cottage . 
OP
OP
rvansnick
Enthusiast
Thanks for all the replies to my question as well as all the great pictures. i think after reading all the posts, that i will likely go with the OEM hood and vent grills. Spring not too far away, time to get one ordered, likely go through VPA. Thanks again
Mamba52
Enthusiast
That's assume as my Viper stays at my cabin in north Georgia the roads are better plus I have the tail of the dragon in my backyard.Thanx Mamba52 ! Sounds good , give me a heads up ahead of time , in case I'm up at the cottage .
VERY common. We usually drill them and use a 1/4" plastic push pin.
JAY
Enthusiast
I'll be Riding the "Dragon" in September , on 2 wheels if your around , let me know !
Similar threads
