Search results

  1. M

    Any msd boost a pump install photos

    I pulled the carpet off the rear deck. There is a round access cover on top that I removed to fish the wires up to the fuel pump and wired it direct.
  2. M

    Dyno Nitrous Results...very disappointed

    I would get six passes on a ten pound bottle. I used a 42 nos / 25 fuel and made 607 rwhp and 700+ rwtq at 1100 psi on the bottle at 11.4 AFR.
  3. M

    Clutch time

    Man I'm sorry guys. I was just looking for some more info on clutches for slightly modified cars. I think the information here fits in with all the others I've read. Stock- Is a good clutch but falls short Others - nobody cares for
  4. M

    Clutch time

    Dave. I can get 1.6x 60' times on pilots and 1.4x on BFG D/R's . I think I can drive
  5. M

    Clutch time

    Alan last time we talk I thought you were going with a ROE. Good to hear you stepped up to the TT
  6. M

    Clutch time

    Now y-all can see my dilemma. data supports trying stock clutch one more time. Votes so far stock 2 Spec 0 Centerforce 0
  7. M

    Clutch time

    What series on the RPS did you go with ?
  8. M

    Clutch time

    I thought you had a Spec 3+
  9. M

    Clutch time

    I have used the Search. I'm on my second stock clutch, didn't last a year, 661 rwhp 697 rwtq . Try stock one more time or go with Centerforce or Spec ???? TIA
  10. M

    Motor question

    Thanks Chuck
  11. M

    Motor question

    I can visible see the drivers side is about 1/2 inch higher then the passengers side. I put a level on top of my ROE and its defiantly out of level.If I loosen all mounts and level it up I should be ok ?
  12. M

    Motor question

    Can someone tell me if the motor should sit level or slightly lower on the passengers side. Thanks
  13. M

    Roe 8 lb with Water/Meth

    Is it newer then 1999 and have some T's in it ?? I'll call you tomorrow.
  14. M

    Kennys Viper progress?

    DUDE :buttkick:
  15. M

    Broken Ring Gear Bolt

    When its time to put it back together make sure the carrier bearings are seated all the way into the housing,, DO NOT USE THE BEARING CAPS TO SEAT IT.
  16. M

    Broken Ring Gear Bolt

    You need to use two common screwdrivers or small pry bars and pop it out. Don't drop it ... :nono:
  17. M

    Broken Ring Gear Bolt

    Your setup should stay the same. The back lash is set buy the shims pressed between the carrier and the differential bearings. you should be fine. just my .02 Buy all new ring gear bolts 70-90 ft.lbs Bearing Cap Bolts 65 ft.lbs Cover Bolts 35...
  18. M

    Roe 8 lb with Water/Meth

    I'll see if I can get that printout.
  19. M

    Roe 8 lb with Water/Meth

    First full day of test and tune is Aril 1st. Midrange I'm adding 6.5 degrees right now on 93 octane, I want to get more aggressive on the timing with some race fuel. You doing Vegas this year?
  20. M

    Roe 8 lb with Water/Meth

    After finding the time this winter to install the T&D's I got from Mike,( 99 R/T 10) the weather was good enough to go dyno. The best #'s so far were, 624 rwhp, 661 rwtq. Roe 8 lb Water/Meth, T&D's, K&N's, Smooth Tubes, Cat- back with no Cats New #'s with some work still to do...
  21. M

    Roe Dyno Run

    Almost as good as yours http://www4.forum.viperclub.org/showflat.php?Cat=0&Number=799669&an=0&page=0#Post799669
  22. M

    Why would my Viper LOSE 80-110 Horsepower coming from Florida to Ohio?

    You should post this on the dark-side, you might get more replies
  23. M

    cats and insulation question

    Go with the R/T metal substrate, the ceramic only lasted two years on my Roe.
  24. M

    will removing cats on a 99 throw any codes

    1999 is a questionable year for simms, from what I've found most do not need them.
  25. M

    will removing cats on a 99 throw any codes

    I have a 99, with a Roe, No cats and no codes.

Latest posts

Members online

Total: 1,114 (members: 9, guests: 1,105)

Forum statistics

Threads
153,198
Posts
1,681,912
Members
17,696
Latest member
Viper123456

Share this page

Top