Recent content by Racer Robbie

  1. R

    '04 Shifter Detent/Centering

    Got to agree 100%. Every shifter i have installed I have done from under the car on a lift.
  2. R

    Battery Tender

    Still have the original battery in my 2003 viper and it has never let me down. It gets down below zero here in CT, and it starts up fine. What you need to do is wire in a battery tender. I installed mine on the shelf in front of the brake master cylinder and wired it to the hot post on the...
  3. R

    Wheel Hop

    I replaced the motor and transmission mounts with Woodhouse/Snake-Oyl mounts, mounted Michelin NON Run Flat PS2 tires and the wheel hop was eliminated.
  4. R

    Absorbed Glass Matte Battery

    Still have the original battery in my 2003 viper and it has never let me down. It gets down below zero here in CT, and it starts up fine. What you need to do is wire in a battery tender. I installed mine on the shelf in front of the brake master cylinder and wired it to the hot post on the...
  5. R

    Correct tire pressure to run?

    We run 34 Front and 30 rear with Michelin PS2 tires, this takes out some of the push or under steer that is dialed in at the factory stock setting of 28 psi.
  6. R

    Will the JET-61610 skip-shift eliminator work for the SRT coupe?

  7. R

    Warrenty Question

    I have a 2003 that I bought brand new and it came with a 7-70 powertrain warranty. The rear diff is part of the powertrain. The question here is simple. Did Alan have the 7-70 powertrain warranty transfered to his name when he bought the used 2003 viper? If so it is covered. If not then he needs...
  8. R

    H/F cat install question

    Got to agree with "VicTxV10" above. We have never had to replace the clamps with new ones. just be careful and take your time. They will come off and they can be reused.
  9. R

    Will the JET-61610 skip-shift eliminator work for the SRT coupe?

    Yes the 60610 will fit. So will Hurst Part# 155-0100 C.A.G.S.SKIP SHIFT KIT. Solenoid is on the driver side and you will have to remove the belly pan which takes less than 5 minutes. Total time for the job is 15 minutes on a lift. :drive:
  10. R

    Gen III Intake manifold removal

    That's Mopar for you!
  11. R

    Mysterious Black Smoke

    IMHO Vipers are not made for drag racing. They are road racing cars. Road racing cars do not drag race. Case in point here: have you ever seen a SCCA Trans-AM race car car drag race at a road racing circuit? If you want to drag race buy a Mustang or a Dodge SRT-10 Challenger. As I stated above...
  12. R

    Gen III Intake manifold removal

    You can reuse the intake manifold gaskets if you like, but considering the time it takes to R & R the intake manifold, I would replace them. Here is the part number from Mopar. 5037-217AC INTAKE MANIFOLD GASKETS, Qty 2 needed
  13. R

    H/F cat install question

    If you Adjust Rear Edge Of Exhaust Tip, 64' Cold & 64-1/2" Hot, from the Metal Wheel Inner Fender Support By Front Cat you will be pretty close.:2tu:
  14. R

    air filter on 08

    This seems to be the problem with the new 2008 ECM Emissions standards. My 2008 Miata did just this when I installed a K & N Filtercharger Kit. It ran like crap and threw a code. I replaced the kit with a K & N replacement filter, reset the ECM, and all was well.
  15. R

    Pulled over for race car on street

    Yes, here in Connecticut on I-95. Told me I accelerated to fast and wrote me a $400.00 ticket. Judge threw it out as there was no written police report on file.
See more

Latest posts

Members online

Total: 602 (members: 8, guests: 594)

Forum statistics

Threads
153,219
Posts
1,682,091
Members
17,715
Latest member
SKY1960

Share this page

Top