Recent content by WCKDVPR

  1. W

    OS Giken Differential in Viper

    Thanks for all the information. Now that some time has passed, is there any additional input that owners of the Giken and or Quaife have at this time - especially those who have experience with both? I am looking at replacing the the posi unit in my track only (road course), Hoosiers/slicks, 645...
  2. W

    2007 24' Haulmark trailer listed in classifieds

    I have a 20' Haulmark with bench, cabinets, tire racks, etc. It is 3800 lbs empty. I installed a generator and compressor. My car is 2850 lbs and I carry two additional sets of wheels/tires, jack and stands, some brake rotors, tool box, and miscellaneous parts to the track. I tow it with a...
  3. W

    $$$ Control Arm Bushing Replacement $$$

    Sean, as an upgrade from stock, how do these new poly busings compare to the delrin ones that have been around for a number of years? Wow, for $2100 you could almost do monoballs, not that you would necessarily want to run those on a street car.
  4. W

    '96 GTS Sway Bar Rates?

    Thanks Tom, that is a old, but great book. I saw that on page 150 but also thought the Viper bars were hollow. Maybe that should be my next question. Does anyone know if they are hollow or solid. (I'm too lazy to check the density). I could probably just do the math OD, length, weight.......
  5. W

    '96 GTS Sway Bar Rates?

    Does anyone know the front and rear sway bar rates on a 1996 GTS? Thanks very much!
  6. W

    '96 GTS sway bar rates?

    Does anyone know the front and rear sway bar rates on the 1996 GTS? Thanks so much!
  7. W

    Slicks vs DOT race tires

    Hi Slammed, Lots of great advice from a bunch of guys with tons of experience. I definitely second the fact that with slicks you are going to need track pads and without any front cooling, you will go through them quickly. And they are expensive. Also the performance brake fluid is a must for...
  8. W

    need some motor rebuild advice

    Mike who got the car together last night and just finished signing up for the Angen Event on this Friday, that Mike. Can't stay for the weekend, but I will be getting back to the track...finally. See you there!
  9. W

    need some motor rebuild advice

    Treesnake, I had read all the stuff on the boards about Arrow being good and when I needed a shortblock done I went to Arrow. They selected the pistons and recommended their own rods (modified 340 hi-po rods). They polished and balanced everything and then assembled the entire motor (with my...
  10. W

    need some motor rebuild advice

    Get a hold of Kevin Singleton at Exotic Engine Development in Temecula, CA. He did the GTS-R motors in the glory years (Le Mans victories)and still builds most of the FIA motors for the European Teams. A lot of the road race guys use him for motor work. He really knows his stuff. Contact info...
  11. W

    Help - I need a Gen 2 block

    I bought the one from JonB. Thanks all. Best regards,
  12. W

    Help - I need a Gen 2 block

    Help please, I broke a rod and need a Gen 2 block to get my engine back together again. If not a bare block, I would be interested in a Gen 2 short block. Prefer that to be from the forged piston years. Thank you very much! Best regards, Mike Please contact me at [email protected]
  13. W

    HD U-joints?

    My U-joint between the drive shaft and the diff doesn't seem to like the new motor. I spit it out last Friday at Buttonwillow. Does anyone make a heavy duty one for a '96 GTS? Also, do you know what the part number / type is? Thanks for your help. Best regards,
  14. W

    Hey DC, the GTS just got its butt kicked at the "RING".

    Re: Hey DC, the GTS just got its butt kicked at the The Viper in question was tested by Auto Sport Magazine with the magazine's chief editor as the driver. The test was run on a Eurospec Viper GTS on 10-1-97. From the official Nurburgring website: Horst von Saurma (D) Chrysler Viper GTS, 411...
  15. W

    Quartermaster triple plate help!

    Please help, I have a Quartermaster triple plate clutch in my '96 GTS and it is not functioning properly. I spoke with Quartermaster and they say that I need a throw out bearing cap they manufacture that fits over the front of the stock T/O bearing. My install was done incorrectly and a spacer...
See more

Latest posts

Members online

Total: 769 (members: 10, guests: 759)

Forum statistics

Threads
153,215
Posts
1,682,039
Members
17,708
Latest member
xeng yang

Share this page

Top