Search results

  1. G

    3.55's to be installed

    Have a set of cheap summit gears in a car running 8.60's with a 1.23 60ft.... I kinda have to say bullcrap on that. Been there for two seasons. Ring and pinion is ring pinion... not viper specific. Yes there are differences and price ranges, but I think he will be fine with that. Arnt you the...
  2. G

    Aeromotive pump controller and tach signal

    I'm hooking it up... the tach signal wire doesn't cut it and that driver didn't work either. I called Aeromotive and they said this controller will not work properly on a viper without the MSD tach signal adapter. Said I should also run the signal booster because i will be running my pump...
  3. G

    Aeromotive pump controller and tach signal

    thanks guys... I will look to verify that I have the correct wire. If I don't, i will correct it... if I do have the Tach signal wire, i will switch to a inj driver as J. Dell Suggested. the 20% off wouldn't pose a problem as the controller is adjustable. thanks
  4. G

    Aeromotive pump controller and tach signal

    I hooked up the Aeromotive pump controller on my 95 as per the instructions. I pulled the tach signal from the upper PCM, Cavity 43 GY/LB. I started the car and the pump runs with none of the LEDs lit on the controller. When I hit the override switch, the green SWT light comes on. From what I...
  5. G

    Fuel sending problems after upgrading

    thanks, you were right. I pulled the tank and found that I did have it connected properly. It was a bad sending/level unit. thanks.
  6. G

    PBJ Cold air intake on Gen 1?

    I had purchased a catch can from JMB and it was better than expected. I'm about finished with my car and wanted to install that beautiful Cold air box and tubes on my 95 Roe with meth. It really looks like a clean install. Has anyone installed on Gen1? I was looking at the "long" version...
  7. G

    Fuel sending problems after upgrading

    A little background on my 1995 RT: I pulled and freshened my motor with some new goodies and also installed a 10lb ROE. I retained my NX system so needed to upgrade my fuel system. I removed the stock fuel pump and sumped my factory fuel tank. Ran -10 to filter and A1000 fuel pump, up to a...
  8. G

    hood pad question

    hi guys, my 95 rt10 was factory green and had been painted viper blue. will a 96 hood pad fit my car the same? :dunno: Looking at the hood pad from R and J that has the blue viper logo. thanks :usa:
  9. G

    Roe blower seized; time for Turbos???

    +1 This is what I would do in your case, as it is the most reasonable thing to do. Any way you go, maintence is the key to survival.
  10. G

    need rings for stock pistons

    I called Diamond and they do have them. He told me years vary and didnt know if i needed the 1.5mm or 1/16" 1st and 2nd ring. Can anyone help? I broke my mic. I know 1/16 works to be 1.57mm and they are not the same set. thanks
  11. G

    need rings for stock pistons

    Hi all, Installing a ROE 10psi on my 95. Looking for piston rings as i pulled the motor and had the cylinders honed. Really didnt want to, but I was that far and they didnt look great. Did a search and didnt come up with much. I'm looking for brand and part numbers for good rings for my stock...
  12. G

    Todays Track Day Videos

    Nice, I like to see videos of Gen1's being ran, rather than sitting in the garage.
  13. G

    San Antonio TX......Anybody near there ???

    I'm here in San Antonio. Got my baby apart right now. Upgrades.... Roe and goodies

Latest posts

Members online

Total: 994 (members: 11, guests: 983)

Forum statistics

Threads
153,234
Posts
1,682,246
Members
17,728
Latest member
booth

Share this page

Top