you know, ime always open minded, perhaps since the majority of our cars are not race cars makes a difference. ALSO...we are not wrapping THE HEADERS......we are wrapping down stream 2-3 feet where the metal(i believe) is much cooler than an ACTUAL header. I had a $1299 header on the Mitsu from...
:bs2:
HHMMMM
1: Disguise heat????irrelevent....Contain the heat??? correct!! Postpone the heat????? irrelevent again. Contain the heat and send it out the tail pipe is what were after Disguise and postpone the heat mean nothing....
2: Corrosion and oxidation....well maybe...
wow, i just did the rendom tech cats and wrapped both sides with 2" header wrap. Its the thermo-tec 2000 degree stuff that is impregnated with a copper color substance. I had it on the hotside of my turbo car and it worked perfect. So i would guess it would work on the NA viper. I even wrapped...
these cars flex so much there isnt much you can do. I have experienced all the above.....I have even stripped out the grommit in the sportbar/drivers side.........ime thinking about developing a spring type latch to anchor it down under pressure. Hard to explain. But it might be a winter...
is this a reputable company?????if so, i might do the same. Shops here in Tucson SUCK......i wouldnt trust them with a Yugo.....Is this shop in Phx??? Ray
Maybe, i was up to $550 i think and found out the one he had wouldnt fit our car, so i withdrew the bid. He was from Canada. I contacted Tator to verify part numbers...The seller had his years wrong. Ime going to have to bite it and get a new one....plus ime hearing that used ones can have...
My last Dyno pull at Rob'z shop showed me 20 hp less with the 3rd gear pull than with the 4th gear pull. Back to back. Personally, i would rather have real world HP numbers on a Mustang. Dyno-jet numbers are quite often higher. But that isnt the issue. You always do pulls on the SAME dyno so as...
Well i was at the paint counter for 2 hours......couldnt decide.....they had a hard time getting the Lambo orange in Dupont Chromabase. Alot of the colors were not in the system..and there are like 6 different oranges....soooo I went with........Viper GTS Blue.......i wanted a lighter color, yet...
Ime leaning toward GTS Blue with silver stripes......but i like Hemi orange too.....and Sublime green.......damn, i have to start dropping off parts tommarrow!!!!!! Any other ideas??
Its black with silver stripes. It was picked up at auction in Vegas by a lot here in Tucson. I sure wish i knew who owned it. I bet they still have the sport bar pad laying in their garage!!! I NEED IT!!!:D Ray
UH...O.K.....well, ime not sure what else to check on the car to see if its stock. It has had the head gasget upgrade!! The tranny is new.....rear end clunks..bad.....it does have the K&N square filters in the stock box..I dont see a vec on it...i think its stock.....and as far as the dyno...
ime not positive its stock. But its the factory exhaust, air box, no CEL's, I just bought it with 55k miles. Ime not sure what else could be done to it that i havnt seen yet.:dunno: I ordered a K&N intake. Ive bought 10 of those airbox clips and have lost them all again. Ime so done with that...
i think it did quite well for a bone stock gen 1.......i hope you can see the chart.....it was quite hot today....Ide like to get it up to about 500 ft lb of torque......:headbang: Well its hard to see...
3rd gear pull on the Mustang Dyno was tq=432 hp=346 spd=105 tmp=87 hg=27...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.