Recent content by vjjack04
-
Where to buy it.
prodiver, I do not know what they actually use, but if no one gives you that info (what the factory used), you can use SEM seam sealer, or something like it. This stuff dries very hard but stays very slightly flexible. Its what the auto body shops use for many seam seal purposes... SEM 29392...- vjjack04
- Post #2
- Forum: SRT10 and SRT10 Coupe Discussions
-
Vibration between 1000 rpm and 1800 rpm
I think the car runs and drive good and I don't hear any other noise. I have had it up on the lift and can't find any issue. If it not the balancer, seems like it might be something associated with the throw-out bearing...- vjjack04
- Post #7
- Forum: General Viper Discussion
-
Vibration between 1000 rpm and 1800 rpm
Steve, thanks. Interesting. I imagine if that were the case (the lifters had turned) it would eat the thing up real fast. The car runs very well and I just replaced the spark plugs. The looked remarkably well, considering, they did look like the car has been driven most of its 18k miles a low...- vjjack04
- Post #5
- Forum: General Viper Discussion
-
Vibration between 1000 rpm and 1800 rpm
Woah, you went right to the worst case...no metal in the oil. I did, however, check the balancer, and it seems to be perfectly fine. I'm now thinking it may be mariginally misfiring at that rpm range. I check my spark plugs and they seem to be burning fine, but some decent carbon build up. They...- vjjack04
- Post #3
- Forum: General Viper Discussion
-
Vibration between 1000 rpm and 1800 rpm
I've notice my car (2008) has a vibration between 1000-1800 rpm. I notice it when with the clutch pushed in or with it out (but not in gear). When I drive off or on the throttle I can't tell if its there or not.... The balancer looks fine while its static, but I did not take a look at it while...- vjjack04
- Thread
- Replies: 6
- Forum: General Viper Discussion
-
Gen 2 License Plate Frame Fitment
These work really well...- vjjack04
- Post #6
- Forum: General Viper Discussion
-
New Battery and now I have no power
Migsot, Check the battery to see if it will take a charge. If it's been marked (when purchased) it will show the date. It might be very old. If you can't check it take it to Autozone or some place like that.- vjjack04
- Post #15
- Forum: General Viper Discussion
-
How do I get a feel for a Viper before I commit to buying?
Gramobda, I know this isn't what you are asking, beyond driving a friends car or driving the car you intend to purchase, I do not know how you'd get the feel of driving one (realistically). However, I do have some related points. I bought a '08 coupe a few months ago. It was relatively low...- vjjack04
- Post #19
- Forum: General Viper Discussion
-
window regulator repair
An update. I got the re-enforced window track/regulator back within a total of 4 days, sending it to them, then the repair and them sending it back. Put the thing in and all is fine. So, the problem is fixed. Thanks to all who provided advice.- vjjack04
- Post #16
- Forum: SRT10 and SRT10 Coupe Discussions
-
window regulator repair
ok. It is $375.00 for the repair. It is overpriced, but one other good point is it has a "lifetime" warranty.- vjjack04
- Post #15
- Forum: SRT10 and SRT10 Coupe Discussions
-
window regulator repair
GooglesP, It cost me $29 to ship it UPS, but I am only 3hrs 15 minutes away from their facility in Phoenix AZ. From FL, you'll have to go to the UPS site to calculate. I needed a 30" x 24" x 5" box at about 8-9 pounds. Send to these folks: Power Window Repair Rebuild & Return Services 2439 E...- vjjack04
- Post #13
- Forum: SRT10 and SRT10 Coupe Discussions
-
window regulator repair
After talking to these folks [email protected] I have decided to send it to them (2 day turn around). You can see they modify the original to make it more sturdy and just as functional.- vjjack04
- Post #11
- Forum: SRT10 and SRT10 Coupe Discussions
-
window regulator repair
Ok, I am finally back to this. Removed the window regulator assy. yesterday. Hardest part (to me) was moving it from inside the door to the outside. The instructions at Havik Performance were very good...- vjjack04
- Post #10
- Forum: SRT10 and SRT10 Coupe Discussions
-
window regulator repair
Thank you. I will let y'all know how it goes....- vjjack04
- Post #9
- Forum: SRT10 and SRT10 Coupe Discussions
-
window regulator repair
I will try to remember to make some notes and take a few pictures.- vjjack04
- Post #7
- Forum: SRT10 and SRT10 Coupe Discussions
