Search results

  1. S

    Paxton SC Air/Fuel dyno help

    I have an '04 as well, totally stock engine/Paxton kit with Mopar cat-back exhaust plus ATI damper and DLM intercooler. I had mine tuned with the split-sec box and picked up ~70 RWHP, it did 640 with the stock tune, 710 after the final tune was in. My tuner said they could have gotten more out...
  2. S

    Spark Plugs for Paxton?

    I'm running stock Champion plugs with .032" gap. Mine's an '04 with stock Paxton pulley, Mopar cat-back exhaust and custom tune. I also installed an ATI damper and DLM intercooler for peace of mind. So far I've got about 6K on it with the blower and it runs perfect. Make sure you put the 8:1...
  3. S

    20" Michelin PS2 rear tire - what size?

    20\" Michelin PS2 rear tire - what size? Ok - I'm about to order a set of 20x12.5" and 19x10" wheels with tires to put on my '04 white mamba. I'm going with the Michelin Pilot Sport PS2 tires but I can't decide whether to go with the 335/30-20 or 345/25-20 on the rear. Specs on both vs. stock...
  4. S

    T-56 synthetic transmission fluid?

    I'm thinking about installing a Hurst shifter, might as well change the tranny fluid at the same time. Anyone know if the stock tranny fluid is synthetic or not - if not, any suggestions on a good synthetic fluid to replace the stock fluid?
  5. S

    Anyone tried these Moton/KW Alternative?

    Has anyone tried the coilovers for SRT-10's that Snake-Oyl sells? Saw them yesterday on their website, shock manufacturer not mentioned buy they do use Hyperco springs.
  6. S

    700 HP Gen IV Viper?

    Ok - here we go, let the rumors begin! I am no expert and do not have any inside information but I received this info via e-mail from a friend, I have no idea who it was addressed to either - it could be BS but could be true also - thought it was worth a post...... :2tu: The following was...
  7. S

    Paxton Install Complete!

    For anyone wondering about the Paxton kit - do it, you will NOT be disappointed. The install wasn't too bad, it took me a few weekends to complete but I finally finished it last weekend and had my car dyno'd today. In the 95 degree Texas heat it pulled 640.5 RWHP and 574.2 RWTQ. My only other...
  8. S

    Power steering fluid

    Does anyone know exactly what type of hydraulic fluid to install in the power steering system for '04 cars? Service manual says DO NOT use ATF - ONLY use Mopar or equal power steering fluid, however the fluid I siphoned out of the PS pump reservoir is red (looks like ATF, maybe its ATF+4?), the...
  9. S

    Loose harmonic damper bolt!

    Hey all, just for your info - I started installing a Paxton kit on my car this weekend (it's an '04 white mamba) and got to removing the stock crank pulley. I am putting on a new ATI damper so I proceeded to get out the breaker bar and socket to remove the bolt holding the damper onto the crank...
  10. S

    Boost and Fuel Pressure gauges/mounting pod

    I'm gearing up to install a Paxton on my '04 and I want to install both boost and fuel pressure gauges in the cockpit. Does anybody know of a company that sells a gauge pod/mount for this application, preferably a dual a-pillar pod for 2-1/16" gauges? I looked on the autometer website and they...
  11. S

    Paxton Installation

    Has anyone out there installed a Paxton kit themselves? I just ordered the kit and was planning on putting it on myself, but having a local shop tune it, mostly to make sure the A/F ratio is on the safe side. My car ('04) is bone stock except for Mopar exhaust, 3.45 gears and K&N (which...
  12. S

    RSI in Houston

    Anyone have any work done on their car at RSI in Houston? I'm considering using them to install gears in my '04 and would like some feedback before letting them touch my car.
  13. S

    K&N Install - LOUD Noise?

    Ok, I put on a K&N FIPK kit last night (I have a bone stock 2004), the install was easier than I expected. I followed the advice I read on previous posts and drilled out the fitting for the hose connection on the RHS of the K&N inlet tube with a 7/32" drill bit as this hole was tapered...
  14. S

    Skip Shift Eliminator

    Hey all, I'm officially a "newbie", just took delivery of an '04 white mamba last week (#84 of 200). As most of you, I can't leave it stock so I ordered the K&N FIPK and Corsa Track system today. Read the posts on the skip shift being eliminated with the K&N and I will be careful...

Latest posts

Members online

Total: 923 (members: 3, guests: 920)

Forum statistics

Threads
153,241
Posts
1,682,307
Members
17,738
Latest member
iliyanaclark657

Share this page

Top