Recent content by ACELLR8

  1. A

    New rubber for the old snake

    500 us dollars for a 335/35/17 here. Getting much harder to find.
  2. A

    Aussie RT10 check engine light gen 1 1995

    See if this helps. Will at least tell you what the code is. ON-BOARD DIAGNOSTICS 1. Cycle the ignition key ON-OFF-ON-OFF-ON within 5 seconds. To cycle the ignition key ON means to turn it only as far as it takes to get the radio to come on. It does not mean to turn the engine on. 2...
  3. A

    Radiator Fan Fuse/Relay 95 RT/10

    There is no fuse (fused link instead) for the fan. First I would check the relay under the passenger side heater air box, that was the culprit on my fan failure a couple years back. You can jumper with a paper clip between relay pin # 87 (high speed fan) or pin # 87Q to pin 30 12 Volts, hot all...
  4. A

    Looking for a Gen I rear diff for my 95, anybody have one they want to sell?

    I am looking for a rear differential for my 95. Must have blown out today. Not sure if anybody has had these rebuilt, but figured it might be easier to buy a used one and replace. If you have one and would like to sell it you can email me at [email protected] Thanks, Ed Rist
  5. A

    Where to find a 96 RT-10 Dash? Anybody have one or know where to get one?

    I am trying to help a friend of mine locate a dash for his 95 viper. I suggested he put the solid black textured dash from the 96 into his 95. As we know he Gen I dashes are junk. He does not want to go the painting route like a of people including myself have done. He prefers OEM / Stock...
  6. A

    Gen I Electric Fan not working, Any tips or ideas appreciated.

    Ok well I finally got a chance to look at this tonight late after Kids soccer games, homework and getting them to bed. :omg: I think I finally will have to admit defeat by 1 95 Dodge Viper. Doug I checked everything you mentioned and really did not see any corrosion. I did learn that at the...
  7. A

    Gen I Electric Fan not working, Any tips or ideas appreciated.

    I just went home and grabbed both new relays and checked. I have continuity between Pin 30 and center pin 87Q. No continuity between Pin 30 and Pin 87. I hope I am reading these relay numbers correctly. Does my drawing above of what pins are what match up with what you believe they should...
  8. A

    Gen I Electric Fan not working, Any tips or ideas appreciated.

    Ok worked on this again tonight, now I am convinced I am really ******** or had too many gin and tonics:crazy2: I ran a new hot fused wire to the remote battery post to what I believe is pin 30. All seemed good until I put the relay in and the fan came on instantly even without the key in the...
  9. A

    Gen I Electric Fan not working, Any tips or ideas appreciated.

    Allan, Thanks again for the info. I am confident tonight I will get it resolved with your information. I was kind of thinking what you were about running a new fused wire to the back of Pin 30. Your help is much appreciated! I will keep you posted and this thread posted! Ed
  10. A

    Gen I Electric Fan not working, Any tips or ideas appreciated.

    Allan I checked the pins last night as you mentioned with a volt meter. Here is what I found. I found that pin 86 has 14 volts when the ignition is on, pin 30 has no power at any time. The fan kicks on when I jumper 86 to 87q or 87 with the ignition on. I then checked the fusable links...
  11. A

    Gen I Electric Fan not working, Any tips or ideas appreciated.

    Allan, Thanks soo much for the info that is the what I needed to know is where the pins on the relay went. I am gonna check the things you mentioned tonight and see how I make out. Thanks again! Ed
  12. A

    Gen I Electric Fan not working, Any tips or ideas appreciated.

    Been trying to figure out why my Electric fan on my 95 Viper is not coming on. So far this is what I know, when I jumper accross the relay connecter with a wire the fan comes on, so I would believe that is telling me the Fused link is good and that the fan is good. I have so far replaced the...
  13. A

    First and last

    Cool Pic!! The Gen I still looks Bad A$$ too, even next to that sweet TA Viper.
  14. A

    Who has chromed their gas cap?

    It has been couple of years, but from what I remember you just take the little plastic grey pins out, with a punch. When I did mine they did not want to stay in after I re-assembled it so I bought some hardware at Lowes where the one side threaded into the other pin. Worked perfectly.
  15. A

    Lowered Gen 1's on stock 17's?

    What kind of springs are you looking to use? I have Intrax on my 95 and love the look. Here is a pic with 17" HRE's.
See more

Latest posts

Members online

Total: 926 (members: 6, guests: 920)

Forum statistics

Threads
153,199
Posts
1,681,914
Members
17,696
Latest member
Viper123456

Share this page

Top