Recent content by Big E

  1. Big E

    Gen 1 Sidepipe Paint Protection

    I have some of the NOS paint protection film for the Gen 1 side pipes. When I was thinking about reproducing some I noticed that the OE pieces were really thick. I couldn't find anything that thick. Maybe it was thicker to withstand the extreme heat. That upgraded thermal insulation is the way...
  2. Big E

    1996 Window Outer Door Glass Weatherstrip

    Back in 98 or so, I took my 96 GTS to the dealership for some warranty work. They told me there was a "TSB" (I think that's what they called it) on those weatherstrips. The two piece is assembly line correct but the one piece looks good to me.
  3. Big E

    2000 RT-10 over heats when the air is turned on?

    Is your electric fan coming on? Sometimes fried wiring and/or relay burns up. Heard of a bad ground for the fan too. See attached screen shot.
  4. Big E

    96 Viper GTS valve cover differences?

    I was curious about that too since my car isn't too far behind yours. So, I was board one night and did a search of completed auctions on Mecum, Barrett-Jackson and Bring A Trailer. The latest Vin I saw, number 270, had the drivers side filler cap and every car I found before that had it on the...
  5. Big E

    GTS third brake light out (sneaky Pete)

    Good information to know. Thanks for posting.
  6. Big E

    Front Licence Plate Holder?

    https://www.viperpartsrack.com/front-license-plate-bracket
  7. Big E

    Question on rear boot

    I bought a couple boots from a seller on eBag. The main problem, they are overseas and it took a couple weeks to get them. So if you have time and your links are not worn out; Dust_boots
  8. Big E

    Drilled brake rotors 97 GTS

    What he said on the drilled. EBC is a good rotor. They have some that are dimpled that look like they are drilled. Dimpled + slotted would look really good. I went with the slotted from Roe Racing. Summit Racing has a nice selection of EBC's. Summit Racing
  9. Big E

    Fixing Viper Flaws

    I like the idea of the T-nuts. I was in a hurry and used those plastic drywall anchors with some glue. They are holding good but I'm sure I'll be replacing them again someday.
  10. Big E

    Motor mounts and trans mount needed

    Trans mount; https://www.stevewhiteparts.com/oem-parts/mopar-transmission-mount-4643318ac Engine mounts; https://www.stevewhiteparts.com/search?search_str=Engine%20Mount&ptid=5552 Shop rate for a install; No clue here. It's best to call your local dealer and ask. Almost every time I go to a...
  11. Big E

    2002 RT Full Borla Exhaust

    My Mopar Performance system was too loud for me. Mine was louder without the cat so I just left it out and added a Magnaflow to it. Sounds good to me now.
  12. Big E

    Throttle cable clips

    Interested here too!
  13. Big E

    Crankshaft Pulley too far in (misaligned)

    Hope someone here helps you soon. Makes me want to install the pin kit that I've been putting off: Roe Racing Kit
  14. Big E

    Borla Cat Back

    I'd replace the stock cat with high flows. But first, try adding a "test" pipe in place of the cats and see if you like it. Mine was too loud so I added a small Magnaflow in place of the cats to get the sound I liked. When it's time for state inspections the cats go right back in.
  15. Big E

    GTS exhaust question

    You'll be fine. Maybe if you tracked your car then I'd make sure everything is 3".
See more

Latest posts

Members online

Total: 938 (members: 11, guests: 927)

Forum statistics

Threads
153,227
Posts
1,682,173
Members
17,717
Latest member
06Quad

Share this page

Top