Recent content by Jack B

  1. J

    OBD2 scanner

    Along the sme lines, I have a Witech that I am going to sell. This is the same format the dealers use. You can extract data that the typiocal OBD scanner cannot see. As an example you can log PIDs such as knock sensors if you are tuning.
  2. J

    Forgeline - Skinnies - Plus Rears with New MT Mounted

    Steve You are close enough, I could meet you half way.
  3. J

    Forgeline - Skinnies - Plus Rears with New MT Mounted

    I am getting ready to put these up for sale: A Fronts{ Forgeline wheels only Rear: Forgeline with new MT DR
  4. J

    Cleaned Out the G2 Spare Parts Cabinet

    Cleaned out the Parts in the Gen2 Cabinet Just a little heads up, I am going to post some G2 parts in the "For Sale" section this week. I would like to sell them as a complete package, in other words one purchase/one individual. I do not have a...
  5. J

    Head Gasket replacement - Who has done it themselves?

    Burping is an art, however, since I started filling at the heater, there has not a problem. You do have to install a tee. They are available in any auto parts store, even Walmart has them.
  6. J

    Head Gasket replacement - Who has done it themselves?

    1. The ARP assembly lube will give you the percent of torque reduction, it is dramatic. If you use the assembly lube and use full torque, you will probably damage the threads. 2. Make sure all the liners are not raised above the plane of the block. 3. While you are in there, you might want to...
  7. J

    Head Gasket replacement - Who has done it themselves?

    We are on the same page, measure twice and cut once. The first time i tried to bolt down a set of viper heads, I noticed the torque readings were not consistent as I tightened down the heads, it was the less than perfect threads in the block, since then, I always use the thread chaser. You can...
  8. J

    Head Gasket replacement - Who has done it themselves?

    Why don't you list the questions. One thing you do not want to do is rotate the engine with the heads off, these cars have liners. Personally, i would use a thread chaser to clean the head bolt threads in the block, that is not tap, a thread chaser is far different. Make sure you clean the head...
  9. J

    M&H Slicks and Skinnies for Sale

    The ad should come alive shortly, these are classic CCW wheels with bias ply M&H slicks and skinnies mounted. They all have been road force balanced. The buyer will pay freight, however, I ship from a commercial account, so the cost will be minimal.
  10. J

    New Viper Owner- Tech Question

    Define using our - qts/miles??
  11. J

    My Fellow Americans...it was a GOOD run

    The Republican party is going to win in 16. The viper will continue to dominate the track. You should really watch some pdv and nine ball's roll races.
  12. J

    Boomerang Mud Flaps for Gen 5

    Do a search on the VOA and vca for center caps, he is a member. If I find his info I will post it. He was excellent to deal with.
  13. J

    Boomerang Mud Flaps for Gen 5

    The first production run is almost gone, Mark only has a few left. I am going to enter an order for another 100 sets, just a guess, we should have them in approx three weeks.
  14. J

    Boomerang Mud Flaps for Gen 5

    Bob Woodhouse is selling them for $79.00
  15. J

    Boomerang Mud Flaps for Gen 5

    I cannot post a picture, the pics are on the VOA site
See more

Latest posts

Staff online

Members online

Total: 1,034 (members: 4, guests: 1,030)

Forum statistics

Threads
153,836
Posts
1,686,656
Members
18,447
Latest member
naimsito

Share this page

Top