Search results

  1. S

    My Supercharger /Heads Project Begins

    Roe recommends replacing them and they give you the replacements with their kit. The ones they send have the clips. They say the stock clips suck and will cause problems. Gary
  2. S

    My Supercharger /Heads Project Begins

    Are you replacing the injector clips? The first couple were a b**ch. After I got the hang of it they weren't so difficult. let me know if you need some tips. Luckily they threw in some extra connectors;) Gary
  3. S

    My Supercharger /Heads Project Begins

    Got the S/C today. Almost done but I will have to wait about a week some parts to get powdercoated.
  4. S

    Looking for I-Forged distributor

    Their customer service sucks- but the wheels are nice. I bought on a group buy from the alley. Gary
  5. S

    Lower with Koni ACR Shocks

    Thanks Guys! Gary
  6. S

    You got through to Chrysler!!

    Hooooooooooooray for the good guys!
  7. S

    My Supercharger /Heads Project Begins

    Here I have the Roe heads that have been surfaced installed along with the T&D rockers. Should have the s/c later this week. Does anyone have instructions for the s/c so I can read up on the installation ahead of time? Thanks Gary
  8. S

    Lower with Koni ACR Shocks

    The site doesn't say anything about raising or lowering the ride height. Does anyone with an acr know if you can do this, and how it is done? Thanks Gary
  9. S

    Couple opinions needed!! FAST

    Can the 02 bungs be welded to headers without taking off the sidesills? Thanks Gary
  10. S

    Installation of MSD Fuel Pump Booster

    Just in case anyone else needs these- MSD Fuel Pump Voltage Booster Installation Instructions 1. Remove Driver’s rear wheel. 2. Remove two black plastic push-in fastners holding whee lwell to body. One is toward the front, at the bottom. The other is toward the back, and also holds the...
  11. S

    Lower with Koni ACR Shocks

    I always thought they were. Maybe I was mistaken?
  12. S

    Lower with Koni ACR Shocks

    Can anyone tell how it's done? Thanks
  13. S

    T & D Pushrod Length

    I will do that- Thanks
  14. S

    T & D Pushrod Length

    Thanks- Sean said the same thing.
  15. S

    T & D Pushrod Length

    Hi, I am installing a set of Roe heads and am putting my T & D rockers on them. The pushrods that I have from my original T & D install are 7.60. Measuring with an adjustable pushrod at TDC on cylinder 1, with the rocker 1 turn down, I am getting a length of 7.579. The heads have been surfaced...
  16. S

    Any msd boost a pump install photos

    I know it's been a while. Can you tell me where you accessed the fuel pump wiring. Did you have to remove the rear driver wheel well to get to the wiring? Also do you know the colors of the wires? I have been having a hard time finding any info on this. Thanks Gary
  17. S

    Installation of MSD Fuel Pump Booster

    TED, When I installed my vec I didn't use the vacuum line, I used my cars map sensor instead of the one in the vec. I was told by Dave at Roe that there were 2 ways of doing it and this was the better way. I don't know if that applies with the s/c though, since I am just getting my s/c now...
  18. S

    Installation of MSD Fuel Pump Booster

    Simms, If you remember- do you cut the existing wires to the fuel pump and replace them with the msd wires, or are they tapped into the existing wires? Do you access these from under the car, or from inside the trunk area? Looking at the diagram it looks like you are cutting out the fuel pump...
  19. S

    Installation of MSD Fuel Pump Booster

    Hi, I bought one of these in preparation of a s/c setup and have some questions before I start. The switched power to the relay #86- Any reason I can't use the same power line going to the vec? The line from the msd relay 85 to the "original fuel pump relay" - I get that from the pcm - grey...
  20. S

    My Supercharger /Heads Project Begins

    That's exactly what Tator and a few others have told me.
  21. S

    Hoodpad logo design - need opinions

    Fist one with stripes is bad a**
  22. S

    My Supercharger /Heads Project Begins

    BTW am I nuts or is my service manual wrong. I was putting the wires back on the coils and referred to my 99 manual. It was completely different than how I had my wires. Not merely reversed but totally different. I downloaded an image off the web site and it matches how my coils were wired.
  23. S

    My Supercharger /Heads Project Begins

    After a broken jack messed me up yesterday I got some needed help from my son. It was a lot easier with the hood off, but it is a messy and time consuming job. Especially scraping the gaskets off the block and thermostat housing. There must be a better way:confused:. Here is today's progress.
  24. S

    My Supercharger /Heads Project Begins

    Is this fairly accurate- Camshaft Removal 1. remove rockers, pushrods 2. remove heads 3. remove alignment yoke and remove tappets 4. remove generator 5. remove air cont. compressor - drain oil 6. Remove crankshaft pulley & damper 7. remove crank oil seal 8. remove timing chain cover and chain...
  25. S

    My Supercharger /Heads Project Begins

    PS pump and pulley are done as is pinning the crank. But my low profile rapid pump jack just took a dump on me. This is the secong one I had do this.

Latest posts

Members online

Total: 1,085 (members: 6, guests: 1,079)

Forum statistics

Threads
153,839
Posts
1,686,670
Members
18,450
Latest member
Bcanfield

Share this page

Top