Search results

  1. D

    Seat Belt (Harness) eye bolt...where to buy

    Going to put in a "racing" harness in my SRT-10. Would like to use quick disconnects with eye bolts. Where has you all bought them......z What's the thread size??
  2. D

    Seat Belt Mounting Hole on Transmission Tunnel

    Hey...some measurement of where the center of the bolt is would be great. If you could measure from the rear floor "corner" going forward and then up. Thanks Mark
  3. D

    Seat Belt Mounting Hole on Transmission Tunnel

    Been looking for the bolt hole on the transmission tunnel for the "inside" part of a 5 point harness.....been pokin' around with a needle.......(I could have disassembled the entire interior in the amount of time I have been poking around....but then again when I go fishing......I know going to...
  4. D

    Accusump run to Engine Block??

    Have not checked into this but I "heard" the cooler has a valve that stops flow under certain conditions...like if the a/c is on....also might require a check valve to flow the oil the correct direction....
  5. D

    Accusump run to Engine Block??

    Have a SRT-10, 2005, and would like to run an Accusump system. Current plan is for a 3 Qts unit hidden in front of right front wheel well cover. ie Between fog lights and black plastic fender liner. Fits fine and the run is short. BUT RATHER than a "sandwich plate" between the block and...
  6. D

    Need seat belt hole positions that are under carpet.

    Looking for the location of the 5/6 point seat belt threaded hole postions that are under the carpet. Been trying to feel thru the carpet to no avail. Anybody have some measurements before cutting?? 2005 vert Mark
  7. D

    Babbling Exhaust CPU driven??

    I have a 2005 vert and I do love the exhaust sound. Have a sort of have a bet with some buddies about the noise. I noticed that the burrble when you coast only last a certain amount of time, regardless of RPM, roar grade etc. Do you think this "Letting off the gas burrble" is actually...
  8. D

    Idle (is normal) a bit like a miss

    Only owned a V-10 in a Dodge truck. But my new Viper has a (very) little roughness at idle. Simular to mild cammed V-8 or an old odd-fire GM V-6. Did not expect this with production car. Normal??? 05 Vert. thanks, dunce
  9. D

    How to KILL Ignition????... Pre-Oil sitting Viper, MORE help Please....

    More pre-lube How do I kill the ignition power??? I am going to remove plugs, Spray WD4O or fogger and spin with starter to prime. Plugs out, so much less pressure on main and rod bearings. And prior to that add a quart or two of oil at a high rate to flood the area around "all" the pushrods as...
  10. D

    Pre-Oil sitting Viper, MORE help Please....

    How to KILL Ignition... Pre-Oil sitting Viper, MORE help Please.... How do I kill the ignition power??? I am going to remove plugs, Spray WD40 and spin with starter to prime. Plugs out so much less pressure on main and rod bearings. And prior to that add a quart or two of oil at a high rate to...
  11. D

    Pre-Oil sitting Viper, MORE help Please....

    Thanks for the post. So no distributor...so cancel the power drill pre-lube. Thank for the insight on the Fuel pump relay. THINKING now....Plugs out, little mist oil in cylinders (Fogging oil or WD-40), Add about a quart and a half....so as to flow down the push rods and maybe hit the cam on...
  12. D

    Oil Pre lube.....Car sitting 8 months......

    I just bought a 2005 convert that has been sitting indoors,climate controlld conditions. HOW can I prelube the engine to prevent a dry start. Can I spin the oil pump as in other cars via the distributor shaft?? If not, HOW can I kill the ignition (with pulled the spark plugs) so as to spin...

Latest posts

Members online

Total: 272 (members: 4, guests: 268)

Forum statistics

Threads
153,247
Posts
1,682,342
Members
17,742
Latest member
Mpcc

Share this page

Top