Recent content by Big Jimbo

  1. B

    2004 Tremec Speed Sensor Question

    My problem is that I installed the 2004 engine and trans in a hot rod project and don't have the ABS or other sensors. I wanted to tap directly into the pulse generator for a signal for the speedometer. Here is a link to my project car. Thanks!
  2. B

    2004 Tremec Speed Sensor Question

    I am trying to figure out which pin on the connector has the pulse from the speed sensor for the speedometer. I have attached a picture of the plug and sensor. I am going to use an aftermarket speedometer that has a wire that needs to pick up the pulse. Thank you very much for any help! I...
  3. B

    Where To Mount Temp Sender?

    Thanks. The sender looks similar to the stock sender with the same threads. I was hoping there was a removable plug somewhere, but it sounds like drilling and tapping will be necessary.
  4. B

    Where To Mount Temp Sender?

    I have installed a 2004 Viper engine in a 1959 Plymouth and after 3 years almost have the project drivable. :rolaugh: I now am installing aftermarket gauges (Stewart Warner Maximum Performance) and can't figure out where to mount the sender for the water temp gauge. It says not to wire it into...
  5. B

    Help needed with Wiring Harness

    I have installed a 2004 Viper engine and transmission in my 1959 Plymouth :D and am fixing a wiring harness to make the engine run stand-alone. Does anyone have the shop manual picture of the Speed Sensor Pin-out for the Tremec transmission speed sensor for a 2004 Viper? The sensor in the...
  6. B

    Wiring help needed!

    That's what my speed sensor looks like. Does anyone know what colors the wires are to the plug? I think in the wiring section of the manual in the Pin Out section it shows a picture of the plug and tells the color of the wires going to the plug. Thanks!
  7. B

    Wiring help needed!

    I have installed a 2004 Viper engine and transmission in my 1959 Plymouth :D and am fixing a wiring harness to make the engine run stand-alone. Does anyone have the shop manual picture of the Speed Sensor Pin-out for the Tremec transmission speed sensor for a 2004 Viper? The sensor in the...
  8. B

    Gen 3 Stand Alone Engine Wireing Harness

    I just contacted DC Performance and they said they didn't make the engine harness. OOPS, this wasn't DC performance. I haven't heard back from them yet.
  9. B

    Gen 3 Stand Alone Engine Wireing Harness

    I sent some pictures to Hammrhead. I am to the point where I now can install the harness. Is DC Performance the place to get one made or are there any other sources? Thanks, Jim
  10. B

    Gen 3 Stand Alone Engine Wireing Harness

    Twin Turbo, I can't figure out how to attach a picture to this site. Is there a link on how to do this?
  11. B

    Gen 3 Stand Alone Engine Wireing Harness

    Thanks for your help Dan!
  12. B

    Gen 3 Stand Alone Engine Wireing Harness

    I just installed a Gen 3 engine in my old Plymouth and was hooking up the original wiring harness and computer when a friend of mine told me it would never work. I was told I needed to get a stand alone racing harness. I have done a search and found many of these for sale for GM applications...
  13. B

    Would Gen 1 or 2 gauges work with Gen 3 Engine and Computer?

    That seems to make sense. What I think I will do is hook up a mechanical oil pressure gauge and try to get it started. If it seems to run OK I will go with the analog gauges. If possible I would like to just use the Viper harness for the engine and use the original Plymouth wiring for...
  14. B

    Would Gen 1 or 2 gauges work with Gen 3 Engine and Computer?

    Dan, sorry I wasn't clearer with my question. I am installing a 2004 Ram Viper engine and transmission in a 1959 Plymouth. The engine is complete with all accessories, sensors, and wiring intact. I have all of the wiring from under the hood including the computer and fuse-box module. The...
  15. B

    Would Gen 1 or 2 gauges work with Gen 3 Engine and Computer?

    Thanks Dan. Do you know if it would it be very difficult to hook up a direct oil pressure gauge and Tachometer?
See more

Latest posts

Members online

Total: 904 (members: 10, guests: 894)

Forum statistics

Threads
153,233
Posts
1,682,242
Members
17,728
Latest member
booth

Share this page

Top