Recent content by Dave149
-
D
Pics from the 2012 Carlisle All Chrysler Nationals
Hey that's my Dad's Superbird! Originally used as a pace car at Sunset Speedway near Barrie, Ontario Canada. Its debut after a 16 year restoration! It was a pretty good show this year although it was way too hot, especially for us Canadians!;) I didn't bring a car this year as I hauled my...- Dave149
- Post #24
- Forum: General Viper Discussion
-
D
Anybody with a Bright Blue metallic Viper going to Carlisle?
My Dad wants to paint his 1969 Barracuda convertible Viper bright blue but he has never seen the colour in real life. Pictures don't do that colour justice, so I am hoping there will be one at Carlisle he can look at. Anybody? The Barracuda will have a 6.1L Hemi with a 5 speed manual...- Dave149
- Thread
- Replies: 2
- Forum: SRT10 and SRT10 Coupe Discussions
-
D
How many people from Ontario are here?
Like many others, look often, post little. :D- Dave149
- Post #14
- Forum: Canada: Ontario
-
D
Car grinding going into reverse. Help!
I had the same problem a couple of years ago. It started to happen right after I went to shift hard into 5th, but the reverse lockout didn't work and it tried to go into reverse instead. The shift fork bent when it wouldn't go into reverse. Could this have happened to you Chad?- Dave149
- Post #34
- Forum: RT/10 and GTS Discussions
-
D
Canada Represents! Viper Days in Canada!!
Steve. I signed up quite some time ago, but I would love to be a passenger for a couple of laps in a Comp Coupe:D Dave- Dave149
- Post #4
- Forum: Viper Racing
-
D
Daytime Running Lights Question
It goes on the passenger side of the aluminum brace behind the radiator. The plug should be hanging around there somewhere.- Dave149
- Post #3
- Forum: RT/10 and GTS Discussions
-
D
How fast in the 1/4 Mile?
Last year with my 2000 GTS with the original tires, 3.54's, Borla cat-back, and cone filters, I ran a 12.8@118. I had only drag raced a couple of times before that but not in a Viper. I would figure a stock ACR would be close to that, maybe a bit quicker with an experienced driver. BTW the...- Dave149
- Post #12
- Forum: RT/10 and GTS Discussions
-
D
Clutch Lowering Kit
I just put the Roe kit in my gen II, and I found the pedal assembly was loose! The bolt that was loose is accessed behind the PCM on the left side (under the hood) of the foot well. The entire clutch master was moving quite a bit when the clutch pedal was pushed. Not sure if the gen I is...- Dave149
- Post #15
- Forum: RT/10 and GTS Discussions
-
D
List your Winter Mods
RPM Transmission level V with alternate 5th/6th ratios, Aluminum flywheel, EBC Redstuff pads, Stoptech s/s lines, clutch pedal lowering kit, setup pedals for heel toe shifting, and cat delete. It sure sounds nice with the Borla cat back. Can't wait to drive it with the new ratios and the...- Dave149
- Post #23
- Forum: SRT10 and SRT10 Coupe Discussions
-
D
EBC Redstuff pads with temp sensor?
Thanks to everybody!! JonB, I didn't get them from you only because my local distributor could get them and shipping to Canada is extremely expensive. I will need to order a couple of things before spring from you though. I will give you a call soon. RobZilla - The pads in the pictures on that...- Dave149
- Post #13
- Forum: RT/10 and GTS Discussions
-
D
EBC Redstuff pads with temp sensor?
Thanks ViperTony. I guess I will cut the wire off and install.- Dave149
- Post #7
- Forum: RT/10 and GTS Discussions
-
D
Just saw an 2008 DODGE CHALLENGER in Traverse City Michigan
Probably a pre-production vehicle out for testing. There are several pics on the web of them without any cladding on them at all. They look good, but it's too bad they won't put the 6 speed in it until 2009.- Dave149
- Post #5
- Forum: General Viper Discussion
-
D
EBC Redstuff pads with temp sensor?
I've never seen an electronic wear sensor system before, but like I said, I have no idea. RobZilla. They are for my Viper (front).- Dave149
- Post #5
- Forum: RT/10 and GTS Discussions
-
D
EBC Redstuff pads with temp sensor?
I just picked up my new redstuff pads, and the fronts have a wire coming out the top of two of the pads (one for each side). I have never seen this before and couldn't find any info about it on the EBC website. Does anybody know what this is for? The only thing I could think of is a temp sensor...- Dave149
- Thread
- Replies: 12
- Forum: RT/10 and GTS Discussions
-
D
Shifter Bushing?
RPM Transmissions in Indiana offers a bronze bushing. rpmbronzeinsert.html Dave- Dave149
- Post #6
- Forum: RT/10 and GTS Discussions
