Recent content by lxadeuce

  1. L

    Where's VENOM V ?

    just so i know, since i'm a viper owner but not a "paying" member, who is off limits to talk about or face the ban hammer? with all of the drama, resignations, reappointments, letters about who is bad and who is not, it's gottn confusing. is the forum headed in a new direction already with new...
  2. L

    Where's VENOM V ?

    sounds like big brother got him
  3. L

    2014 SRT Viper site is up.

    how about the glitch when you first click "exterior"? it's the invisible option.
  4. L

    Average MPH: 149 on a new car? LOL

    my motorcycle was broken in that way, dynoed 5.5hp higher than any stock bike that had dynoed in the last 2 years or so
  5. L

    Check Your Clutch Master

    you should have changed the clutch while you were in there. I've been told that anytime the clutch or slave needs to be changed, to do the other so you don't need to drop the transmission again. it's only a couple hundred extra to do it
  6. L

    Fuel Pump DIY?

    I've done that fix. it did help with the starting issue but it will not help with losing fuel pressure at higher RPM's.
  7. L

    Fuel Pump DIY?

    i believe on the 96 RT10 you have to cut the floor of the trunk out. the replacement fuel assembly is around $900. you then get a replacement truck floor and rivet back in place. I'm not 100% certain on this since i have a 96 GTS, but i do remember seeing something about it when i was...
  8. L

    Viper spotted by google earth

    I was just checking to see what the current picture of my house is that google maps uses and it has my viper in the driveway!
  9. L

    DIY "KNG" Custom Gauge Faces

    exactly. i thought the print feed would be a litle more precise since i can print borderless. i haven't learned lot about my big printer at home since i do all roll paper, but i found it a pain in the butt to load single sheets of any size. i know i had to shrink it don to 97% size, turn off...
  10. L

    DIY "KNG" Custom Gauge Faces

    I have a similar printer at home too, the problem is still getting it to line up exactly. I used a good laser printer at my job to get these right and they are still barely off but I got tired of trying after about 15 times so I used the best ones.
  11. L

    $2000.00 service charge( don't know if it is fair or am I being hosed)

    when i developed a leak in my PS hose, it was a $20 part
  12. L

    DIY "KNG" Custom Gauge Faces

    The tach kinda worked but was a little slow to drop the RPMS back down, the oil gauge had a loose wire inside so it would occasionally just drop to zero then bounce back up once i tapped it, the fuel gauge would go up to about 3/4 and just stay there, not sure what the deal was with it. so, i...
  13. L

    Does ADDING stripes hurt the value?

    its your car, paint it how you like it. i buy a car to enjoy and drive, do the same
  14. L

    DIY "KNG" Custom Gauge Faces

    i just got the gauges in that i broke. and have added the different faceplates. the initial ones were only printed on one side but the black background was not dark enough so it let some of the blue light through. I printed front and back on the same sheet of paper and it made a HUGE...
  15. L

    Best comment you overheard someone say about your car...

    i have actually done that... got her to send a naked picture too, she was massive!
See more

Latest posts

Members online

Total: 673 (members: 10, guests: 663)

Forum statistics

Threads
153,215
Posts
1,682,024
Members
17,708
Latest member
xeng yang

Share this page

Top