Recent content by pokeyl
-
Hard Start Gen 3
Can do. the only Part I have not changed is the pos-bat cable the runs to the starter. I did add a jumper cable from the battery to the pos post under the hood. No Change. I still thing it is what I am asking of the car. Many starts with almost ZERO recharge time. The alternator is...- pokeyl
- Post #10
- Forum: SRT10 and SRT10 Coupe Discussions
-
Hard Start Gen 3
The Root cause is starting the viper 20 times, with only a 2 min autocross run to recharge? At the end of the day it wont start. The heat makes it worse. If I drive around town there is never a problem. If I take the relay fuse box cover and open the hood it helps. (bad in the rain) Swap...- pokeyl
- Post #8
- Forum: SRT10 and SRT10 Coupe Discussions
-
Hard Start Gen 3
My Bad. I have had 3 new batteries in the car AGM, standard lead acid, and Litho-ion. some rated as high as 950 CCA. Problems with all of them. I have not changed the positive battery cable.- pokeyl
- Post #4
- Forum: SRT10 and SRT10 Coupe Discussions
-
-
Hard Start Gen 3
Anyone having problems starting any time the battery is not fresh from the charger? I have found the voltage drop when starting makes the starter relay chatter!!! Hard to start. I have changed the Starter and ground cable at the battery. As well as the starter relay, No Difference...- pokeyl
- Thread
- Replies: 9
- Forum: SRT10 and SRT10 Coupe Discussions
-
Corner Balance
Yes, on the Left Rear and Right Front. Cross weight was off 2.5% but the ride height looked good???? Setup Pics with laser level. Took longer to set the pads as my garage floor is not level. I did not expect the cross-weight to stay that close from "empty" to "driver".- pokeyl
- Post #4
- Forum: SRT10 and SRT10 Coupe Discussions
-
-
Corner Balance
Just picked up a race car weight system. Any advice? I'm going for 50/50, left,right with me in the seat. Front to back looks like 49/51 front/rear. Cross will be 50/50- pokeyl
- Thread
- Replies: 3
- Forum: SRT10 and SRT10 Coupe Discussions
-
Cam questions
I did my own Cam, Exhaust, and Heads Labor. Money I saved did a bowl port. Is the tune included? 238/246 @ 0.050'', 114 LSA, about 0.600... Roe 710r cam 620 at the wheels- pokeyl
- Post #2
- Forum: SRT10 and SRT10 Coupe Discussions
-
Motor Mount time any Wisdom
I did not remove anything but the front crossmember. With the car on jack stands, I used an Impact gun to snap off the bottom bolt! at this point you are committed to the change. Jack the motor to support and remove the 3 bolts holding the mount to the engine. Remove and finish taking the...- pokeyl
- Post #8
- Forum: SRT10 and SRT10 Coupe Discussions
-
Motor Mount time any Wisdom
All done, WOW, shifter dose not move under throttle AT ALL.- pokeyl
- Post #6
- Forum: SRT10 and SRT10 Coupe Discussions
-
Motor Mount time any Wisdom
What heat shield are you using for the poly mounts? (non woodhouse) I was thinking muffler repair tape- pokeyl
- Post #5
- Forum: SRT10 and SRT10 Coupe Discussions
-
Hood gas strut support pin BENT
Cool, to the off Junk Yard!- pokeyl
- Post #3
- Forum: SRT10 and SRT10 Coupe Discussions
-
Hood gas strut support pin BENT
Anyone have a source or can I pull one off any car?- pokeyl
- Thread
- Replies: 2
- Forum: SRT10 and SRT10 Coupe Discussions
-
