Search results

  1. J

    power window motor request

    First of all, I would like to give Chuck 98 RT/10 credit for this idea. :2tu: He had suggested that perhaps someone with an entrepreneuial spirit could look into rebuilding the motors. I would like to pursue this as an alternative to trying to source used or hard to find new ones. The motors...
  2. J

    I broke my Roe, dammit...

    I had mine rebuilt by PSE in April. Repalced all bearings, seals, and two gears. Refinished rotors due to slight imperfections. $1,500. Turn around time was approx two weeks. They will strongly advise you not to keep your 10 lb pulley. In fact, they will not install it and void your warranty if...
  3. J

    yes, another side sill repair question

    red heat: Did you still use the stock insulation?
  4. J

    yes, another side sill repair question

    Thanks for all the input so far. Dan, I will call you next week. Bill
  5. J

    yes, another side sill repair question

    I need to have both side sills repaired and have read through nearly every thread on this subject. My 96 gts has headers, Borla, and no cats. The stock insulation is in pretty good shape except for an area on each where the cat was. I will be adding vents front and rear. Has anyone tried a...
  6. J

    Fuel door polish help

    I had water spots and oxidation on my 96 gts fuel door. I started out with 800 wet sanding then 1500. Used Mothers aluminum polish and looks like new. Wet sanding is the key to polishing weathered or neglected aluminum.
  7. J

    questions for those with Autoform side sills

    On my 96 GTS, the passenger sill has some corrosion and paint bubbling. I am thinking about replacing both with the Autoform units and I have a few questions: - How is the quality? - How is the company for customer service? - Did you use the factory insulation or a different method...
  8. J

    Quaife vs. OS-Super-Lock vs. 3.73's vs. steering

    I have a Quaife w/3:33's. Very impressive. I can punch it at about 30-40 mph in any gear but first and wheel spin or not the car stays straight. Also had the stock unit w/3:07's and would not go back.
  9. J

    radiator fan r&r

    Is there a write up or tutorial on replacing the radiator fan assembly in a 1996 GTS? I am putting in the later version for the 99 and up. I did a search and could not find anything. Thanks.
  10. J

    roe supercharger rebuild poll

    I had asked Sean first and he does not do any rebuilding. He suggested PSE.
  11. J

    roe supercharger rebuild poll

    I would like to know who has had their roe rebuilt, by what company, and how durable is the unit compared to factory? Thanks
  12. J

    510 stroker and Roe ?

    That is correct as far as the cooling period between runs.
  13. J

    510 stroker and Roe ?

    How many here are running a 510 and roe with an 8 or 10lb pulley? Also, has anyone ever cooked the fluid in their roe or damaged the nylon coupler after a series of dyno runs? The car went through 10 runs with the 8lb @ 103F with a large fan in front of the car. Thanks.
  14. J

    radiator fan questions

    On my 96, the fan makes a grinding noise for several seconds after shutting down. I would like to get a high output one. - Where can I buy one? - Approx price? - How difficult is it to change? does the rad nead to come out? Already did a search and could not find anything conclusive...
  15. J

    Roe 10lb and PSE superchargers

    I had my s/c rebuilt by PSE and they reused the 8lb pulley. I have since upgraded the engine and want to put on the 10lb. PSE strongly suggested that I don't as it would cause premature failure of the unit. I think its BS since there are plenty of people running this setup with no issues. Has...
  16. J

    questions for those with a 510 stroker

    Thanks everyone for the replies so far. In reference to the heat issues, the ambient temp in the dyno room was 100 F by the 8th pull.
  17. J

    70mm throttle body ?

    I need a set but before I buy, I wanted to see what my options are ie: manufacturers, price, and quality. Thanks.
  18. J

    questions for those with a 510 stroker

    Dynojet dyno
  19. J

    questions for those with a 510 stroker

    My engine builder just finished rebuilding my 96 GTS engine upgrading it to a 510 stroker. It has a rebuilt roe s/c with an 8lb pulley, water meth, reworked heads, 8.5:1 CR, roller rockers, Diamond brand light weight pistons and a blower specific cam. It currently has the stock throttle bodies...
  20. J

    capet dye question

    I bought them from Custom Car Floor Mats, Custom Grilles, Chrome Trim & More - US SPEED and paid $100 incl shipping. Great quality and service. Bill
  21. J

    capet dye question

    I recently bought a new set of black floor mats for my 96 gts. When cleaning the car today, I noticed a brown spot about 2 in dia on the mat. I tried to remove it with several cleaners that I have used in the past with good results. Nothing worked. It looks like a chemical of some sort worked...
  22. J

    question for those with a PBJ catch can

    I have had mine on my 96 GTS for several months and approx 500 mi. I was looking under the hood with the engine running and noticed that oil was misting out through the mini filter on top and oil had dripped down the side. The site tube was empty and there has not been any sign of oil leaking on...
  23. J

    2003-2006 Viper SRT-10 Roe Racing Supercharger Kit Revealed

    Sean, nice clean look and impressive numbers !
  24. J

    Freakin tired!

    Bronze here - N.C. to Florida
  25. J

    gear question

    Camfab, your guess was correct, I am going with twin turbos at some point :headbang: Bryan, do you recognize the sig? You need to take the car out of your sig :D

Latest posts

Members online

Total: 941 (members: 3, guests: 938)

Forum statistics

Threads
153,839
Posts
1,686,670
Members
18,448
Latest member
JpKL

Share this page

Top