Search results

  1. R

    Convince Me! Gen I vs Gen II

    It's only been 3 years deciding. Give a guy a break
  2. R

    transmission/rear end lube

    Gear lube #68003055AB was used. I don't expect that it has a modifier pre-mixed. Would it?
  3. R

    transmission/rear end lube

    Thanks for the correction. Yes. Transmission fluid along with rear end lube and modifier were changed. (Supposedly).
  4. R

    transmission/rear end lube

    Had the transmission fluid and modifier changed in my 2004 (11,000 mi.) changed last October. I'm not sure that the dealer even used modifier. After I asked the service clerk if he did. He looked at me with that blank stare and said "What's that?" He asked the service manager and he said...
  5. R

    Crank pulley photo

    If you could take the bolt to a local machine shop, they could accurately measure the thread for you with a thread gage and pitch mics. I doubt that a service or tech manual would even show the class of thread in the crank though. That's something only a Dodge engineer would know. I would...
  6. R

    2004 Black Mamba

    Was this close "----><-----" to buying #124 last August. Scheduled a Saturday test drive on Thursday. Friday the car was sold out from under me. Ended up buying a non-Mamba SRT-10 in Oct.
  7. R

    2008 Viper ACR Price

    Www.autotrader.com
  8. R

    Crank pulley photo

    The pulley is designed for a press fit on the crank. Make certain that the crank is free of any high spots. I saw a lot of gaulling on your original photo. Be careful not to cut deep into the crank shaft. Takes rime and finness. If you can find a thick washer to place between the head of...
  9. R

    Classic Muscle vs Modern Muscle

    Just come out and ask the little princess to be... Q:"What kind of car am I allowed to buy?" A: "A new mini-van."
  10. R

    Crank pulley photo

    Do you have a set of dial calipers to measure the bolt head? 31mm = 1.220" 32mm= 1.259" 1-1/4=1.250" My experience with stubborn bolts is to use sharp force to break them loose. I would actually cut the open end side of the box wrench off completely so that you have a good solid surface...
  11. R

    Crank pulley photo

    Use a good penetrant and let it sit for a while. Using the shortest box wrench that you have, hit it with a heavy hammer to break it loose.
  12. R

    Rare Viper to be Crushed

    I agree. What possible benefit could come from this. It sounds too stupid to be true.
  13. R

    Crank pulley photo

    The gauling on the crank shaft would indicate that it was just loose and spinning for a while (not cracked). There would most likely be rust in the cross section if it were cracked.
  14. R

    1995 Power Steering fluid question.

    But absolutely do not use anything other than an official Martha Stewart turkey baster. Whatever you do.
  15. R

    Factory installed radar detector volume

    The used car dealer that I bought it from in Bridgeville PA. told me that it was a factory option. Indicator lights for front and rear detection are installed on the dash left of the steering column and it looks really clean like it could have been installed at the factory. I just took his...
  16. R

    Factory installed radar detector volume

    I purchased a 2004 SRT 10 with factory installed radar detection last fall. The device is constantly going off warning me of signal detection to the front or, to the rear. I've had detectors before and know that they pick up a lot of errant signals but, this one talks. It's loud as hell. Has...
  17. R

    different tire size?

    I think that would look silly.
  18. R

    looking at buying an 08 SSG Coupe anyone in OHIO

    I think it's always high at Marshall. Gives them room to negotiate. This car is however very cool looking. Offer them 50 and start the negotiation.
  19. R

    Service Departrment issues

    Oooops...2004
  20. R

    Service Departrment issues

    I just bought my new (to me) 2014 SRT 10 in October 2013. I took it to the dealer for oil and transmission change and filter. I also asked for the differential fluid and slip modifier to be changed. After 8 hours I called and they told me that the car was finished, so I went to pick it up...
  21. R

    What is a Gen III wholesale or Trade value?

    $40-45,000.00 (retail) is the market price.
View older results

Latest posts

Staff online

Members online

Total: 993 (members: 12, guests: 981)

Forum statistics

Threads
153,841
Posts
1,686,685
Members
18,454
Latest member
Mopar SRT

Share this page

Top