Search results

  1. M

    VEC 1 Calibration Problems

    Took my 96 GTS to the dyno to calibrate the VEC 1. Had little or no luck in doing so. Every time I ran a good dyno hp the next one would be all screwed up. When the car was WOT on the bad run, the A/F mixture meter would come off rich toward the lean side by two lights and I would lose power...
  2. M

    2004 YELLOW SRT for VCA raffle

    Just received my Viper Quarterly 4th VCA Raffle - Fall 2003. Offers 2004 YELLLLLLOWWWW SRT with special badging. Tickets $100. deadline is September 19, 2003. Drawing October 4, 2003. Lets see, sell the wifes PT for 18k that would give me 180 tickets sounds like a deal to me. <font...
  3. M

    Engine stalls at idle

    Bump
  4. M

    Engine stalls at idle

    Here's the problem. 1996 GTS. Lost harmonic balancer in Nashville last year, that messed up the end of crank. So this winter I decided to have Arrow engine replace the crank and put better pistons and rods in, while I was so deep into it. :flag. Arrow finishes engine engine runs great. Engine...
  5. M

    Banners VOI 7

    Just received mine today, They are bigger than years past. Came with broken dowel rod, looks like a trip up to Home Depot. Thanks guys hope everyone gets theirs soon. Have a good Thanksgiving.
  6. M

    Banners VOI 7

    Yes, those are the banners I'm talk about, but without the regions name on them. They cost if I remember about $75. They sold some at the registration desk until they were sold out, then VCA took orders after that.
  7. M

    Banners VOI 7

    Has any one received their banners from the VCA, that we ordered at the end of the VOI? I'm talking about the banners that were over our heads at the dinners. Thanks Jeff
  8. M

    First ticket in my Viper, it's all MadMan's fault....

    Re: First ticket in my Viper, it\'s all MadMan\'s fault.... Hi genXgts; Did you say that you were in Michigan when you received your ticket? To the best of my knowledge you don't need front plates in Michigan. Lived here for 44 years, never needed one.
  9. M

    EASE Diagnostic

    Has any one used this software to work on their Viper. Or to scope out problems. Would like to get feed back on how easy to use and all the things it gives you. Thanks Jeff
  10. M

    Air fuel mixture (where to test)?

    Where is the most accurate and correct place and way to check air fuel mixture? Had it tested at dyno, however he just had a tail pipe unit. Wouldn't it be better to take the reading at the O2 senser in the headers before the cats. Thanks Jeff
  11. M

    Need Help on HP Problem

    Yea I got the Images to work. Finally I'am going to see my viper tech tomorrow to see if the computer lost its upgrade. Thanks for any more suggestion of what the problem could be.
  12. M

    Need Help on HP Problem

  13. M

    Code 42

    My GTS came up with the service engine light. After doing the code check by watching the number of flashes, it came up 42. However when I looked in my service manual, I see three differant things listed for 42. Is there a way to find out which one I'm looking at. Thanks Jeff
  14. M

    Need Help on HP Problem

    Thanks racetech for the reply; I don't think its the valve springs but will inspect tomorrow. Have a feeling it's something else but not sure yet. Will try to scan dyno run tomorrow. Thanks
  15. M

    Need Help on HP Problem

    Hi Marv. Thanks for the reply, But I did have the computer flashed back when the TSB came out. I do have a service engine light on and the code is 52 a running rich code. Thanks again.
  16. M

    Need Help on HP Problem

    I have a 1996 GTS, 10,000 miles and the following mods. Larger throttle bodies Smooth tubes K&N Filters 3.45 Rear End Hennessey Headers & Exhaust 3" Hi flow cats 1.7 roller rockers (TNT) Heads flowed and larger valves (TNT) Street-Performance cam (TNT) Aluminum flywheel My problem is 2 weeks ago...
  17. M

    Cylinder compression

    Thanks for the replys, I checked all cylinders on my 96 GTS and the results were between 160-169 so feel pretty good about those numbers. Spark plugs looked good only have about 500 miles on them, a little on the white side, must be running a little on the hot side. Thanks again
  18. M

    Cylinder compression

    What numbers should I get for compression test on my 1996 GTS, just turning it over with a remote starter?
  19. M

    T&D Roller Rockers Install

    I'm sure this has been talked about before however couldn't find the procedure for installing and checking T&D Roller Rockers in the search mode. Would appreciate if someone could post the installation procedure for the T&D roller rockers. I've had them installed just want to go back and check...
  20. M

    Garage floor epoxy?

    Hi. Just had my garage floor done this past week. I can tell you from experience that everything depends on the preperation of the concrete floor. Had done my own with epoxy 6 years ago on a one year old floor, looked great for 2 years then the epoxy started peeling up in some areas. The worst...
  21. M

    Tinting Glass

    What problems has anyone had with the police on tinting their side windows on their vipers or other cars. Was thinking of having my GTS and my Ram done this next week?
  22. M

    4 Post Lift Collapsed

    I've had a lift in my garage for 9 years with my 92 RT 10 on it and 6 years with my GTS under it, have never had any problems. I believe it goes back to you get what you pay for. I have a Rotary Lift (name brand) this brand is used in all the auto plants for servicing execs cars. Top of the...
  23. M

    Side Sill Insulation

    Need some information on the glue or epoxy that Dodge uses to hold the insulation in the side sill, to the side sill. I would have to think it is a high heat material just can't find one that I would think would work. My insulation came loose when the body shop was painting the side sills. Hate...
  24. M

    Resonator Location

    <BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by Sean of NJ: Are you sure it's not the cats that are getting hot? Because if they are still there, it is them that are baking. As far as the resonators to, just get rid of them if you want or just put a...
  25. M

    Resonator Location

    Has any one moved their side sill resonators to the rear where the original mufflers are set up, on a GTS? My reason is I have Hennessey headers and 3" exhaust, I love the sound, but the resonator fits so tight in the side sill that it gets really hot with no air around the outside of it. Would...

Latest posts

Members online

Total: 918 (members: 44, guests: 874)

Forum statistics

Threads
153,843
Posts
1,686,701
Members
18,455
Latest member
Mando9595

Share this page

Top