Search results

  1. S

    roll on with a 2004 Viper vs my 98?

    Isn't there a slight overall gearing penalty for the SRT10 because of the taller tires? That could play into the outcome.
  2. S

    Belanger Headers...low restriction cats... CORSAs. Anyone with this combo?

    Here is my car Bellanger/Corsa's/no cats + some engine work It'll be a little more muted with cats, but otherwise pretty close Turn it up!!! Viper Exhaust Idle
  3. S

    Who's ran 11's dead stock ( or close)

    They run the car through the 1/4 mile like normal. They then take the time run and plug it into a rather large equation that re-computes the 1/4 time/speed based on standard conditions (not sure on specifics). Depending on conditions, it could go up or down. 99.9% of the time the corrected...
  4. S

    Who's ran 11's dead stock ( or close)

    Just for some clarification, but Motor Trend uses corrected times when they report their numbers, which means the cars never actually turn the times they report. They are the only magazine out of the big three that do it that way.
  5. S

    Any 6''3 Viper owners?

    I never said it was comfy, but I fit w/o a seat lowering kit. And I'm a legit 6'7" 260# in my birthday suit, so no number exagerations here. It can be done. You just gotta be careful with your left knee and the light switch, and tuck the left foot under the clutch when your done shifting. I...
  6. S

    Any 6''3 Viper owners?

    6'7" 260# (athletic build) and fit without seat lowering kit
  7. S

    SCT Flash Programers... Tuned, tested and in stock...

    Will this ever be available for a gen II?
  8. S

    Flowmaster vs. Striaght Pipes.... Sound clips... FINALLY!!!

    Here is mine: Corsa/Bellanger/no cats http://video.google.com/videoplay?docid=2353166865589421745 They all seem to sound pretty close. No cats definitely give it more of a "metal" sound
  9. S

    Rear end alignment - New rear end

    If i picked up an extra rear end assembly with a different gear set, would I need to re-align the rear tires everytime I switched? Or could this be a simple switch? Also, are all years interchangeable?
  10. S

    Hood jammed

    We'll find out this weekend, as the car is up north.
  11. S

    Hood jammed

    The hood is square. I have been describing the hood being in P1, but the more I think about it, it actually is between P1 and P2, but looks like it's in P1. I can barely get my fingers under the hood to grab the lever. Like I said above, what little pressure I can put on the lever, it doesn't...
  12. S

    Hood jammed

    Thanks a bunch for braving the cold for me. I'll be sure to try all this out. The back of the hood is locked down, so I will try to release that somehow. The lever under the hood will not move at all, which is means that I cannot release the rear bracket that hold the back of the hood down...
  13. S

    Hood jammed

    There is about a 2" gap between the two. It is in the position right after you pill the handle through the front grill. The release under the hood does nothing, but feels like it is working. This all happened while I was closing the hood. I keep the car at the lake house, so I will have to...
  14. S

    Hood jammed

    It is definitely in position #1. The trouble is you can't see crap under the hood the way it is right now.
  15. S

    Hood jammed

    Ok, I think it is in position one, right before you make the final "push" to fully close teh hood. That is where it is stuck. I went to push it and nothing, won't budge. Can't lift it back up either. The handle you pull to release pulls normally, so I have no idea what the problem is. I...
  16. S

    Hood jammed

    It won't open or close, it is just jammed. It happened while trying to close. Lowered the hood as usuall, to where there is the ~2" opening before latching. It just won't budge either way.
  17. S

    Hood jammed

    As it sounds, the hood is jammed in the first position after you pull the handle to release and the hood is opened ~2". It is jammed and I'm afraid to put too much pressure to move it. What do I do?
  18. S

    Bellanger header bolt torque spec

    Thanks for the input, but they are already installed. I'll just wait and see if/when they blowout and replace them. It shouldn't be too hard to put a new gasket in when that time comes. What is a good gasket to go with?
  19. S

    Bellanger header bolt torque spec

    Already using them. I'll wait until they blow out.
  20. S

    Bellanger header bolt torque spec

    Yeah, some of the bolts are a pain to get at. I've heard the same about the gaskets, but after taking to a few people, including Lou, they are fine if you properly torque them down.
  21. S

    Bellanger header bolt torque spec

    Anybody????
  22. S

    Bellanger header bolt torque spec

    Anybody happen to know this off the top of their head? I can't find it anywhere. I'm using the provided gasket from Bellanger.
  23. S

    How tall are you Viper owners?

    6'7" 260 with no seat lowering kit. It can be done.
  24. S

    Sound Clip: Bellanger headers/No cats/Corsa

    Yeah, I heard the same exact setup on an '02 and it rumbled way less during idle. Need some decent weather before road videos
  25. S

    Sound Clip: Bellanger headers/No cats/Corsa

    Completely stock other than the exhaust.

Latest posts

Members online

Total: 836 (members: 7, guests: 829)

Forum statistics

Threads
153,217
Posts
1,682,050
Members
17,711
Latest member
techanvi

Share this page

Top