Recent content by PHILIP
-
P
Gen 1 head gaskets/ Is there a need for a cost effective replacement.
I am keen also, Thanks- PHILIP
- Post #26
- Forum: RT/10 and GTS Discussions
-
P
RH radiator hose reinforcing spring
My OEM radiator hose on the right side from the radiator to the engine (the big one) has what appears to be a galvanised reinforcing spring which shows some signs of corrosion. Is this spring important? as I would prefer to leave it out. I wonder if there is potential for electrolysis between...- PHILIP
- Thread
- Replies: 3
- Forum: RT/10 and GTS Discussions
-
P
Motor Oil: 10W30 or 20W50
From what I have just learned Mobil1 0w40 is supposed to be their best oil, 10w30 is not commonly available here in New Zealand Regards Philip- PHILIP
- Post #4
- Forum: RT/10 and GTS Discussions
-
P
hood speaker screw
Was scared of doing that earlier in the week fortunately it did not happen!!. If the magnet does not work you could remove the hood and tip up to make the screw fall out, its only 4 bolts holding the hood and about 6 hands to hold the hood.- PHILIP
- Post #12
- Forum: RT/10 and GTS Discussions
-
P
Question about oil change please......
How much below the full mark on the dip stick is ideal for a little low?- PHILIP
- Post #10
- Forum: RT/10 and GTS Discussions
-
P
Replacing xmas tree clip under front lights
I have just refitted the front bumper, how is it possible to replace the xmas tree clips under the two head lights, or it is Ok to leave them off? Thanks- PHILIP
- Thread
- Replies: 2
- Forum: RT/10 and GTS Discussions
-
P
OEM rear dodge emblem
My original rear dodge emblem has the letters O and D damaged would anyone have either a complete Dodge rear emblem or just the letters that I could buy? Thanks- PHILIP
- Thread
- Replies: 3
- Forum: RT/10 and GTS Discussions
-
P
Air box clip won't stay clamped
Re: Air box clip won\'t stay clamped Bending the clip has worked, as it stays in place in the short term anyway. Thanks.- PHILIP
- Post #20
- Forum: RT/10 and GTS Discussions
-
P
Air box clip won't stay clamped
Re: Air box clip won\'t stay clamped Interesting to know it's the filters? although I lost one with the stock filters. If it is the filter It may be able to be ground or filed down. Thanks for all who offered help.- PHILIP
- Post #13
- Forum: RT/10 and GTS Discussions
-
P
Air box clip won't stay clamped
Air box clip won\'t stay clamped I have a clip that when closed up just slips off the air box, any ideas if it is the clip or something worn on the air box? Thanks- PHILIP
- Thread
- Replies: 19
- Forum: RT/10 and GTS Discussions
-
P
Painting Brake Rotors
I am talking about the edge of the Rotors that are were originaly painted silver on the very edge. Thanks- PHILIP
- Post #6
- Forum: RT/10 and GTS Discussions
-
P
Painting Brake Rotors
My stock Rotors have a little bit of surface rust visible through the silver paint to the edges. I am thinking of stripping rust and repainting, does anyone have any tips for what type of paint to use? (I was planning on a high temp paint similar to what You would paint a manifold with)...- PHILIP
- Thread
- Replies: 6
- Forum: RT/10 and GTS Discussions
-
P
Stock Gen 1 exhaust pic's
Re: Stock Gen 1 exhaust pic\'s The only difference on my 94 is a flexible connection between the manifold and cat.- PHILIP
- Post #4
- Forum: RT/10 and GTS Discussions
-
P
front bumper protection film?
Has anyone used film to protect the underside of the front bumper and if so was it worth the effort, also where else is it worth installing protective film? Thanks in advance- PHILIP
- Thread
- Replies: 0
- Forum: RT/10 and GTS Discussions
-
P
red color code
Thanks for that, I also saw the information is in the service manual together with other manufacturers codes.- PHILIP
- Post #4
- Forum: RT/10 and GTS Discussions
