Search results

  1. A

    setting T & D roller rockers

    so if you went and adjusted all 10 rockers one after the other on one cylinder bank without ever rotsating the crank, aren't some of the adjustments off?
  2. A

    setting T & D roller rockers

    I thought you wanted both valves closed at the same time on the compression stroke when you made the adjustment. Am I wrong?
  3. A

    setting T & D roller rockers

    Is it possible at any time to set the preloads and adjustments on T & D roller rockers without doing the method of going to each individual cylinder, bringing it to top dead center so that both valves are closed, adjusting both rockers, then repeating for each cylinder. I saw someone adjust...
  4. A

    NorCal Bay Area Viper Dyno Tuning

    like i said before, you can get the pulls done, but without aftermarket pcm or piggyback, I doubt you can do any adjustments even with the help of viper enthusiasts. Someone did post a link to ease diagnostics who apparently makes software to hack into the stock pcm, but no one seems to have it.
  5. A

    NorCal Bay Area Viper Dyno Tuning

    if all you want is a dyno pull I did mine at Newtek in Hayward Nicks number is 510-785-FAST He has a dyno jet and is pretty reasonable. I don't know why you would need someone who knows vipers if all you need are the dyno pulls
  6. A

    NorCal Bay Area Viper Dyno Tuning

    I think to do this you would need a way to alter your stock PCM. I remember West Coast Viper saying they could do this, but the reflash was about 500 bucks. If you have a piggyback like the vec 2, then dyno tuning is worthwhile. I'd be curious to know how they are changing parameters on the pcm...
  7. A

    cutouts?

    Does anyone have cutouts on their viper? For those that don't know what it is, A cutout is basically a plate that is removable off of the exhaust pipes, most often located before the cats or mufflers. It can be held on by bolts or you can get electric ones. The purpose is when the cutout is...
  8. A

    List of Modded cars over 500rw

    You got 845 rwhp off those mods? There are people with 10 lb ( 2 lbs more than yours) and headwork not getting those numbers. How is that possible? Most people with your mods are in the low 600's
  9. A

    Need to vent!

    Those are great numbers. I was going on what I learned from Sean Roe. He got 600 with the mods I listed with 93 octane and a 5 lb pulley. When he went to 8 he didn't pick up much hp but torque went up and power fell off a bit earlier because of boost creep. But power under the curve until then...
  10. A

    Need to vent!

    nope-you'll get boost creep and extra torque, but not 600rwhp
  11. A

    Need to vent!

    $7400 will not get you 500 rwhp, try closer to 530rwhp To get to 600 you need headers, roller rockers, 70mm throttle bodies. and either methanol or 93plus octane
  12. A

    Whats involved in changing belt and p/s pulley??

    Mine came out flush using the washer-I used 2 fender washers which are pretty stout. I tried several places to get the official install tool and no one had it. I thought about pulling the crossmember, but wasn't sure if I was going to have a hard time bolting it back up. It definitely would be...
  13. A

    Whats involved in changing belt and p/s pulley??

    having just done it yesterday on my Gen 2 it wasn't too bad. I took the pump off ( 3 bolts-2 hoses). You will need a pulley remover on Gen 2 ( I assume gen 1 the same). Make sure you get a tool that will help put the pulley back on. I used a bolt that fit inside the shaft of the pump where the...
  14. A

    Replacing power steering pump pulley

    Tonight I ran my car up to 5000 rpm and heard a thud. The steering got heavy and I realized I had thrown a belt. Sure enough the belt was off and flipped inside out. As I pulled on the belt I heard something hit the ground and I found part of a pulley. It was what was left of the power steering...
  15. A

    Roe supercharger with/water/meth dyno report

    Re: Roe supercharger with/water/meth dyno report I have heard some people pick up pretty low numbers with belangers. As far as random techs not blowing out, I pulled mine off and they were completely hollow. You could look straight through them as if they were pipes
  16. A

    Thanx to Sean Roe

    Sean is the man. He just spent an hour on the phone with me setting up my vec 2. The settings I got from the original tuner were way off. Half the stuff was not so much software as tech support for my laptop! Thanks Sean!
  17. A

    Roe supercharger with/water/meth dyno report

    what size pulley?
  18. A

    Attn: Roe blower vipers . . .

    here is a link to the guys that port the blowers. They are not doing the manifold but the blower itself. http://stiegemeier.com/flow_results_tb.html http://stiegemeier.com/blower.html
  19. A

    Best Guess for horsepower with these mods

    so you got 670 hp without the methenol? Was this on 91 or 93 octane gas? What is your boost with the 10 lb pulley? About 8.5 with the freer flowing heads?
  20. A

    Attn: Roe blower vipers . . .

    are you saying Sean actually machined out some of the blower casing and polished it for better airflow?
  21. A

    Attn: Roe blower vipers . . .

    Has anyone heard of porting the blower? I know some of the Cobra guys are having the eaton blowers ported. One guy picked up about 50 hp after the porting. I heard the company that did it is going to start porting Kenne Bell blowers which are made by the same mfg. as the roe blower. The guy...
  22. A

    Best Guess for horsepower with these mods

    I just had some new mods for my viper and want to see what you all think my power will be. Keep in mind we have 91 octane gas here in Ca. Old setup 97 GTS, 45,000 miles Roe Supercharger with 5 pound pulley & Vec 2 T & D Roller rockers Valaya 1 & 3/4 in headers going into hi flow...
  23. A

    Recommedations for Tuning Roe blower viper in Bay area?

    Ted said he was unable to do it due to circumstances so I was looking to see if there was a dyno owner that was nearby familiar with vec 2.
  24. A

    Recommedations for Tuning Roe blower viper in Bay area?

    I am getting my GTS back with heads and all the bolt ons and a 10PSI Roe Blower and I need to get a good tune with a dyno here in the San Francisco Bay area ( Ca. ). Does anyone know a facility who is familiar with vipers with a Vec 2 on it?
View older results

Latest posts

Members online

Total: 794 (members: 2, guests: 792)

Forum statistics

Threads
153,843
Posts
1,686,697
Members
18,455
Latest member
Mando9595

Share this page

Top