Search results

  1. S

    And the winner is...

    Congratulations on your new Viper!
  2. S

    CL 55 AMG vs supercharged SRT10

    I looked through your photos hoping to get a glimpse of an A-pillar pod for the SRT :( I have them in other vehicles for boost and EGT, but have not found a pod that I would want in my SRT. TD
  3. S

    Emergency brake relocation

    Archer sells a relocation kit for this purpose. It consists of two machined aluminum blocks, along with instructions. I did mine in the garage without too much difficulty. TD
  4. S

    Best forged pistons & connecting rods for 750-800 RWHP SRT-10?

    Engine is out, so need to move on this decision. Let me know what works best for Vipers in this power range. Lots of manufacturers for both out there, but not my area of expertise. Paxton has stock pulley, but I am considering going up to 10 or 12 psi. What have you used? Thanks, TD
  5. S

    Pipe required to remove cat convertor

    Did you consider removal with a sawzall?
  6. S

    Most collectible SRT-10?

    Not for sale but............... I vote for 2005 Copperhead #001/300 (formerly owned by Me!) :cool:
  7. S

    How long will my clutch last?

    For those who have replaced the clutch, I am curious what brand you used. I know Centerforce has been used by some. What do you recommend? I have noticed some slippage at high speeds (100-120 mph) under WOT situations, and expect to be replacing this in the near future. Thanks. TD
  8. S

    Quality at CAAP

    Re: Quality at CAAP-Give me a answer Yes, it certainly does. More than once in this case!
  9. S

    Quality at CAAP

    My thanks to you Yahllib for responding re: quality @ CAAP. I am on my second SRT-10 and have absolutely no complaints relating to quality on my cars. In fact I would be delighted to tell the folks at CAAP that my current car, Copperhead 001/300, has been mechanically flawless, and fit and...
  10. S

    Lowered Copperhead?

    Thanks. The car was about 1.5" lower after installation. It is adjustable, so that you can raise or lower it as you desire. I had to raise mine almost 0.25" because the tops of the tires would rub on the wheel well liners when moving over some minor bumps. It just takes a couple minutes to...
  11. S

    Lowered Copperhead?

    I have a Moton Club Sport suspension with Eibach springs. There are several photos in my gallery to give you an idea of how the car sits. Here's one of them: TD
  12. S

    Quaife Installed; Best Mod IMHO

    For most Quaife applications, no problem, go ahead and install it yourself. Unfortunately, for the Viper, you will send your differential housing to Taylor Race Engineering in Texas. They will complete custom machining of your housing and proprietary fitment of the new differential. So...
  13. S

    Quaife Installed; Best Mod IMHO

    ILLSMOQ , "carrier"? Glad to help, what are you asking?
  14. S

    Enclosed car trailer

    Glad I could help! TD
  15. S

    Enclosed car trailer

    These: Hope the photo is not too small to see the hooks. TD (Note - the hooks you see attatched to the trailer's D-rings are the same hooks that snap through the car frame's tie-down slots.)
  16. S

    Quaife Installed; Best Mod IMHO

    Vipera, Thanks for posting. I also am in the process of getting a Quaife, for the same reasons you discussed. Others have described these benefits, including the Quaife's seeming ability to straighten the car out when accelerating out of a corner. I think the need for this dif. is more...
  17. S

    Enclosed car trailer

    Yes, I do it this way, too. In the rear, the hook on the tie down strap works just fine without any additional hardware.
  18. S

    Enclosed car trailer

    Got mine from AWDirect. They have a nice catalogue (sent with purchase) with some unusual/hard-to-find items. link here for R hooks and others TD
  19. S

    I dont care what anyone says...

    Actual photo of best Viper ever made:
  20. S

    Under-the-hood Picture of Monton tanks?

    I found this photo , which is not my car. I saved it to show to my Moton installer because the placement of the reservoirs looked good to me . Mine were installed in the front wheel wells, away from the heat of the engine. The photo below is my car, showing my water- ethanol injection...
  21. S

    Supercharging SRT-10

    He means the stock pulley. Art, I was assuming we were talking about dealer-installed systems.
  22. S

    New SRT-10 (pics)

    Bill P. told me pictures didn't capture the beauty of the paint, and of course he was right. Congrats on the car. EVERYONE will notice the color of your Copperhead, sometimes more than the car. Recently at Home Depot, young family near me when parking: "...I don't know what they call that...
  23. S

    How much for a Paxton supercharger?

    Its clear I fuxxored up the data, but wait, the C6 ZO-6 only got a 6.5 :rolleyes:
  24. S

    How much for a Paxton supercharger?

    Hey Ricky, I had to look into this too. Its basically the stage 1, with -more power -better looks -no interior heat -CMI moves from 9.6 to 10.0 (Chick Magnet Index) :headbang: j/k
  25. S

    Supercharging SRT-10

    Your concern is appropriate and understandable. I think you will find the practice occurs frequently. Some 2006 coupes have already been delivered this way. Although the anticipated numbers at first sound impressive, a typical supercharged SRT will have essentially the same specific output (...

Latest posts

Members online

Total: 778 (members: 7, guests: 771)

Forum statistics

Threads
153,215
Posts
1,682,038
Members
17,708
Latest member
xeng yang

Share this page

Top