Search results

  1. M

    Sometimes stalls when coming to a stop.

    Thanks. It's a good point that the gauge may not be accurate. I ran across another thread where someone said the RPM reading from the gauge was lower than whattheir scanner was reporting. I haven't looked at the MAP sensor yet. I understand there's 3 wires. 5v supply, ground and the middle wire...
  2. M

    How to replace an IAC motor on a Gen 1

    The Idle Air Control (IAC) motor is on the back of the intake on the passenger side. You may be wondering if you can actually get it off without removing the intake. Yes you can. Here's how. Tools: 7/16 regular wrench. 7/16 stubby wrench. It's in a tight spot and a regular wrench will hit a...
  3. M

    Sometimes stalls when coming to a stop.

    I have a 1993. As the title says, when coming to a stop my rpms will drop to near zero. It's even stalled a couple of times. At operating temperature the idle seems low. It shows closer to 575 that 704+-25. Yes I am reading the gauge correctly. Yes I realize the first mark just after 0 is...
  4. M

    3D print a case for an ELK-960 timed relay

    Published here: https://www.printables.com/model/526850-elk-960-case I came across this post: https://www.viperclub.org/vca/threads/how-to-build-a-primer-timer-and-cure-your-viper-fuel-pump-starting-problem.624994/ which describes using a timed relay to work around slow-start problem. Though I...
  5. M

    How to build a Primer Timer and cure your Viper Fuel Pump Starting Problem

    For what it's worth, I made a printable ELK-960 box. https://www.printables.com/model/526850-elk-960-case
  6. M

    WTB Gen 1 fog light switch for a 93 RT10

    Phew... I managed to find one at www.viperwizard.nl. It's incoming from The Netherlands.
  7. M

    Website Analysis

    I'm new here. What's the "other" website that's referred to?
  8. M

    1993 stereo head unit removal and install

    I attempted to do this, but I now believe I have to remove the dash. 1) Unclipped the bezel surrounding the radio. I thought just the black part would unclip, but the area around the ashtray and shifter came up as well. The clips are stubborn. I used a plastic pry tool to get a top corner then...
  9. M

    WTB Gen 1 fog light switch for a 93 RT10

    I recently got a 93. I found the fog light switch was stuck. I remove the bezel around it. It looks like someone tried to pry the switch up from the topside. They cracked the trim around the switch and put super-glue to hold it down. Well the superglue flowed into the switch itself!
  10. M

    1993 stereo head unit removal and install

    Thanks. It's a little different for Gen 1. I started searching around for dash removal instructions. Step 2 on the following post suggests it's just simply prying of the radio bezel and a couple of plugs. https://www.viperclub.org/vca/threads/gen-1-dash-removal-instructions.629538/ Perhaps the...
  11. M

    1993 stereo head unit removal and install

    Hi. I've searched the forum but couldn't find any solutions. I have a 1993 antenna car. It still has the original cassette head unit. It mostly works, except when I put a cassette in, it sounds like it's just rewinding, then fast forwarding, then rewinding, etc... and never stops. I suspect the...
  12. M

    3D print a fender seal plug

    Hi. I'm new to this forum. I recently acquired a 1993 Viper. I have lots of questions but I figured I would start by sharing this. My Viper was missing a fender plug. I quickly designed one that could be printed in TPU. Here's the link...
View older results

Latest posts

Members online

Total: 1,172 (members: 13, guests: 1,159)

Forum statistics

Threads
154,442
Posts
1,691,055
Members
19,184
Latest member
MakinWaves

Share this page

Top