Search results

  1. M

    3D print a Gen 1 GPS Mount

    As always, files, instructions, and original OnShape model are available on printables.com: https://www.printables.com/model/850145-1992-1996-dodge-viper-gps-mount
  2. M

    RT/10 GPS mount?

    Does anyone have any clever ideas for mounting a phone or gps to a Gen 1 viper? I feel like I have a few half-baked ideas, but none I'm totally satisfied with. Pictures are great. Product makes and models are appreciated.
  3. M

    3D Print a Green Doohickey

    We can rebuild them. We have the technology! Must be printed or painted green. If not, other Viper owners will point at you and laugh. And you know what? They're right to do so. Never leave home without your doohickey...
  4. M

    Gen 1 wires from trunk to interior?

    I installed some new speakers and they are more sensitive to poor audio signal. With the key on and engine off, I turn on the head unit with volume at 0, and I can hear a high pitched whine. I'm not being picky here, it is a legitimate nuisance. I grabbed some RCA coaxial cable and tested with a...
  5. M

    Power Steering Cap Fix

    This solution might be a bit overkill, but here's how I addressed the infamous power steering cap issue. I routed a 3/8" hose from my cap breather to an oil catch can. 1) It prevents fluid from spraying up and onto the exhaust manifold 2) In the event of the cap coming loose, the hose will...
  6. M

    Gen 1 Audio Upgrade Thread.

    I'm starting a thread for my audio upgrades on my 1993. Gen 2 seems to be well documented in various places, but I figured Gen 1 is different enough to warrant some posts. My goals are: 1) Door midrange speakers (See posts 2 3 4 5) 3) Door tweeter speakers (See post 7) 3) Rear speakers...
  7. M

    Power Steering Cap Gasket?

    Does anyone know if the gen 1 and 2 power steering caps are supposed to have a gasket or o-ring? If so, does anyone know a part number or correct o-ring size? I've been finding conflicting information....
  8. M

    3D print an interior door sill plug

    These should work for 1992 - 2000 This was supposed to be a quick and easy design, but it took some effort to get the button/dome top to not look crummy and to align the layer lines so the legs wouldn't snap off.... Photos and instructions are on the printables.com link below, but In short...
  9. M

    3D print an Air Filter Intake Box Retainer

    I couldn't find a replacement part. I had been using a rubber washer with a squared hole to hold the intake baffle in place. I made a replacement you can print in a flexible filament. More photos are on the printables.com link...
  10. M

    How to replace an IAC motor on a Gen 1

    The Idle Air Control (IAC) motor is on the back of the intake on the passenger side. You may be wondering if you can actually get it off without removing the intake. Yes you can. Here's how. Tools: 7/16 regular wrench. 7/16 stubby wrench. It's in a tight spot and a regular wrench will hit a...
  11. M

    Sometimes stalls when coming to a stop.

    I have a 1993. As the title says, when coming to a stop my rpms will drop to near zero. It's even stalled a couple of times. At operating temperature the idle seems low. It shows closer to 575 that 704+-25. Yes I am reading the gauge correctly. Yes I realize the first mark just after 0 is...
  12. M

    3D print a case for an ELK-960 timed relay

    Published here: https://www.printables.com/model/526850-elk-960-case I came across this post: https://www.viperclub.org/vca/threads/how-to-build-a-primer-timer-and-cure-your-viper-fuel-pump-starting-problem.624994/ which describes using a timed relay to work around slow-start problem. Though I...
  13. M

    WTB Gen 1 fog light switch for a 93 RT10

    I recently got a 93. I found the fog light switch was stuck. I remove the bezel around it. It looks like someone tried to pry the switch up from the topside. They cracked the trim around the switch and put super-glue to hold it down. Well the superglue flowed into the switch itself!
  14. M

    1993 stereo head unit removal and install

    Hi. I've searched the forum but couldn't find any solutions. I have a 1993 antenna car. It still has the original cassette head unit. It mostly works, except when I put a cassette in, it sounds like it's just rewinding, then fast forwarding, then rewinding, etc... and never stops. I suspect the...
  15. M

    3D print a fender seal plug

    Hi. I'm new to this forum. I recently acquired a 1993 Viper. I have lots of questions but I figured I would start by sharing this. My Viper was missing a fender plug. I quickly designed one that could be printed in TPU. Here's the link...

Latest posts

Members online

Total: 699 (members: 7, guests: 692)

Forum statistics

Threads
153,223
Posts
1,682,147
Members
17,715
Latest member
VenomXX

Share this page

Top