Recent content by Doubleup

  1. D

    Nitrogen Kit

    I also have a PowerTank Nitrogen Kit For Sale... like new. Send me a pm if interested. Thanks!
  2. D

    Noisy Tranny

    Mine is a gen 4. Yes noise goes away with clutch pedal down. Up in neutral is at it's noisiest. This is not toi be confused with any clutch noise or anything, strictly just sounds like gears turning... Thinking it is normal, however just wanted to be sure.
  3. D

    Noisy Tranny

    I normally drive my SRT-10 Roadster with the top down, however in winter months have driven more with it up and have noticed the tranny to be a bit noisy especially at traffic lights. In neutral is the worst with clutch disengaged. . Just sounds like noisy gears, nothing grinding or horrible. Is...
  4. D

    Big Thanks To Bbg

    I recently had the pleasure of working with Toddy at Bad Boyz Garage on installing my Gen 4 Sportsman Competition Lightweight Twin Clutch. We did the complete flywheel assembly, his own “BAD BOYZZ SERIES” Stand Driven and Metallic Friction Material Let me tell you this post is LONG overdue...
  5. D

    ASD Fuse Blown at Laguna Today

    Was the rear O2 on passenger side as found from all your help! Thanks Guys! Still bummed I missed my last session and a half on track however at tleast the problem is a minor one! THANKS AGAIN!
  6. D

    ASD Fuse Blown at Laguna Today

    On track today half way thru and ASD Fuse #2 blew and went into limp mode. Replaced and blew imeadiately. What is the ASD do and any clues where to look for a bad device, sensor or short?? Thanks!!!
  7. D

    Question on Caster

    No Comments? Guess we all including myself need a Caster Lesson! Maybe I will Google it!
  8. D

    Question on Caster

    I am getting an alignment done Wed for a track day this weekend. My Specs are 1.9F, 1.0R, 0 Toe F, .2 Toe R. This based on many posts and some trial and error I have experienced myself... I am stuck on Caster. I have read posts mentioning to go anywhere from 5.0-7.0 and only that it depends...
  9. D

    Corner Weighing

    Thanks Mark And Dan. I have another AutoX this weekend and just received my own set of scales so will play with these spring rates for one more event and then if not happy will soften up as Mark suggested...
  10. D

    Corner Weighing

    No Aero... However I am beginning to wonder if my original problem was wrong springs... I had 600/900 7" Eibach's and the rear always felt spongy and would actually feel the suspension bottom out in rear and tires would hit inner fenders in hard downhill corning/apex's. The front tended to push...
  11. D

    Corner Weighing

    Viper X - I am currently running 8" Hypercoils on moton club sports 700f/1000r with 18" SSR's 11" Front and 13" Rear... Not sure the spring rates are the best setup however love the tight feel...
  12. D

    Corner Weighing

    Thanks guys! Should save me some time, could spend a weekend under here looking for perfection. I wish I could just decide on ride height, right now I have about 4.25"F and 5.0"R measuring from frame at axle center point. Not worried about scraping here just the best handling.
  13. D

    Corner Weighing

    Corner weighing my car for 90% track use... It seems the rear wants to be heavier. Am I really trying to hit 50% front/rear? Also besides all the talk of how much to lower a car 3/4" - 1" downd from stock; any recommendations frame to ground (center of axle) front/rear? I have no clue what...
  14. D

    Headers and Intake Installed and Running a Little Funny

    Problem all better! :2tu: Replaced and all spark plugs and problem is gone. No visible damage to any of them however maybe a fine crack of just a loose wire I did not catch. Car is running strong, roads were cold and a little foggy so did not push it too hard tonight... :drive: Funny thing is...
  15. D

    Headers and Intake Installed and Running a Little Funny

    Would love to Dyno the car, just need to find somewhere nearby Monterey... Headers are the Bad Boys Series from Toddy w/Cats, Mopar ECU. I will try to get some miles on tonight and report back. Will probably replace plugs just in case I accidentally damaged one during header install... Must...
See more

Latest posts

Members online

Total: 863 (members: 13, guests: 850)

Forum statistics

Threads
153,187
Posts
1,681,839
Members
17,684
Latest member
Liberty235

Share this page

Top