Search results

  1. T

    Autocross Alignment

    yes it nots difficult if you take your time with good equipment. A well calibrated Hunter machine is what I use
  2. T

    Autocross Alignment

    Thanks for all the positive feed back. In autocross our speeds are low, the car is very stable until until the 4th time out where the slicks are to hot and I start to push through the corner. The rear grip seems fine unless I over power the turn out. I'll try -2 camber up front and leave the...
  3. T

    Autocross Alignment

    I took second place behind the winning time by 1.3 seconds but I was voted the top novice driver and won a SCCA membership for next year. I would like to improve on the current alignment settings I have more for autocross only not as a street car. I feel the car is handling very well but the...
  4. T

    Alignment question

    ASP Man, I only put 4000miles a year on my 2000gts I put on slicks for 3 autocross events a year then the treads for highway driving and around town. I have found what I beleave to be the best all around setup for both tires with no noticeable tire wear. front camber -1.3 toe out .10 of a...
  5. T

    STICKY Slicks

    Thanks to everyone for the input on alignment settings for autocrossing. I won my first event this year. With as many racers that are members on this site I was hoping you might no the answer to this. Sticky slicks mean many stone chips on the wheel well and surrounding painted areas. What do...
  6. T

    Autocross Alignment

    My second auto cross event is this weekend. Just put on a new set of Hoosier A6 tires and did a moderate track alignment. Front Camber -1.9 Caster 6.0 Toe out 1/32 per side Rear Camber -1.3 Toe IN 1/16 per side Did some testing at a local parking lot and what a differance!! I have...
  7. T

    FREE track time at Mid OH

    Leslie, Living in Indiana I have always wanted to drive Mid Ohio. I just purchased a new set of hoosier A6's and would love the oportunity to run Mid Ohio. What is required to run there? My car is a daily driver that I auto cross one weekend a month. My wife just got me an SCCA membership card...
  8. T

    Muffler Delete Pipe with Glass Packs?

    My 2000 GTS has only 1 spiral flow muffler under each side sill and a pair of them where the stock muffler was located at the rear. I cut off the stock exhaust tips from the original setup then welded them back on after the spiral flows at back. I must say sound is very crisp and only loud at...
  9. T

    ROAD TRIP

    Every time you fill up the gas you get people coming up and talking to you about the car and where I headed to next. Driving down the highway I get the thumbs up often. My license plate is I8AVET and a vet even gave me the thumbs up running 90 down to Florida last year.Looks like I will make...
  10. T

    ROAD TRIP

    Glad to hear that Vipers do well on long drives without issue. Knock on wood that will continue for me.
  11. T

    ROAD TRIP

    is your viper black with silver stripes it looks it from your avatar. Funny as mine is that color combo
  12. T

    ROAD TRIP

    I live in Indiana. I have driven my 2000 GTS to New York and just last year down to Key West Florida. All without any kind of issue. I am planning a trip to California just to drive down PC1 and see the sights. My Viper just turned over 40,000 miles today. I have to say I LOVE this car! When I...
  13. T

    So I pulled the cats and my car now sounds like crap, what should I do

    I have a gen 2 with stock manifolds down to a 3" flex braided section from summit then to 3" tubing I bent myself. Then I run the Moroso Spiral flow muffler under the side sills and again in place of the factory muffler in the rear. Total of two mufflers each side. Sounds awsome at under $200...
  14. T

    Viper Registry Data Incorrect On Cam

    Enter your data into the camshaft calculator. Works very well.
  15. T

    Viper Registry Data Incorrect On Cam

    Wallace Racing - Automotive Calculators I used this web site as it has many good calculators.
  16. T

    Viper Registry Data Incorrect On Cam

    What brought this hole thing about was the fact my 2000 service manual shows differant numbers when it came to Exhaust open and close degrees. So after laying all numbers out on a degree wheel to verify the service manual was correct and the viper reg was not.
  17. T

    Viper Registry Data Incorrect On Cam

    I used the stock OEM cam in my 2000GTS and the intake center line method to find the data. I did this to compare to the 708 from year 99 I installed into the same engine and used the same data gathering method. I found the lift value to be true to the registry on year 99 at .541 and 542 on the...
  18. T

    Viper Registry Data Incorrect On Cam

    The Viper registry has the 2000 cam specs the same as the 96-99 in the open and closing degrees on the intake and exhaust. This is incorrect. I question this as the 96-99 cams have 6 more degrees of over lap. Long story short here are the proper cam specs for the 96-99 year 708 cam and the 2000...
  19. T

    SCT - Hands On

    Dan, Thank you. LM-1 will be the way I go. Seems easy enough to use that to hold the info then download it all into the computer where the PCMSCAN software can table the data. Thanks again your knowledge is greatly appreciated!!!
  20. T

    SCT - Hands On

    Dan, I have the SCT 9550 and willorder the PCMSCAN software. What do I use for the wide band input? And can I pick up that input through the OBD2 port? Can the wide band be wired in that way?
  21. T

    708 Cam installation centerline " Lumpy"

    Thanks, I have the degree whell installed and waiting as I enjoy watching the kids in the pool. I'll talk with Greg.
  22. T

    708 Cam installation centerline " Lumpy"

    Everyone that has installed a 708 cam as a factory replacement cam. I would like to no what centerline you installed it at or the amount you advanced it or retarded it. Was the cam very choppy at idle after your install? I am trying to find out where to install my 708. I understand that advance...
  23. T

    Cylinderhead Question For The Motor Builders

    I already have the 708 all I need now are the lifters. I went with the 708 for mainy reasons. Sound, small power increase over what I have and the fact that it is still hydraulic and easy on the valve train. I drive my car from Indiana to Key West Florida to New York just for fun during the...
  24. T

    Cylinderhead Question For The Motor Builders

    Thanks, I completely missed the lifters being bleed down. Thanks again plan on cam swap soon.
  25. T

    Cylinderhead Question For The Motor Builders

    I need to no if the 708 cam that was installed in the 96 to 99 GTS using the same stock valve springs as the later model GTS 2000 to 2002? Do you know what the spring pressure was at installed height on the 96-99 gen2 I would like to remove the cream puf cam from my 2000 GTS and install the 708...

Latest posts

Members online

Total: 824 (members: 7, guests: 817)

Forum statistics

Threads
153,218
Posts
1,682,059
Members
17,714
Latest member
potterb4

Share this page

Top