Anyone know where to get rolled edge exhaust tips?

[bwhitmore]

I want to get some rolled edge tips on my exhaust system, to replace the slash cut ones. I have scoured the internet but to no avail. The closest I can find are Meg's slick tips, but they have the Meg's logo stamped into them, and I want something that is clean.

Any ideas?

 

[jimandela]

I love the B&B catback exhaust tips. They are awesome!!
Maybe B&B will just sell you the tips?

 

[J DAWG]

You can order tips from Summit, Jegs, or JC Whitney. Up to 4 inch fit fine as long as they are not more than 8 inches long. 4.5 will fit but are really tight.

 

[bwhitmore]

I am looking to swap the tips on my Snake Oyl rear sub. I don't mind how far the tips stick out, in fact I kind of like it better that way, but I just want something with a rolled edge.

I see JC Whitney has a 2-1/4" to 3-1/2" rolled edge tip by APC that is 8" long. Would that work? I think 4" may be a little too big at the end.

 

[sbkim]

ViperMed has nice 4" tips - I have them on my snake oyl.

 

[sbkim]

http://vca2.viperclub.org/forums/showflat.php?Cat=&Board=UBB14&Number=366553&Forum=UBB14&Words=snake%20oyl&Match=Entire%20Phrase&Searchpage=0&Limit=25&Old=allposts&Main=366553&Search=true#Post366553

 

[garolittle]

ViperMed has nice 4" tips - I have them on my snake oyl.

Same here.

 

[bwhitmore]

Those tips look great from the back, but I think they are way too short and stubby looking from the side. That is why I figured the longer tip would look nice.

 

[J DAWG]

I am looking to swap the tips on my Snake Oyl rear sub. I don't mind how far the tips stick out, in fact I kind of like it better that way, but I just want something with a rolled edge.

I see JC Whitney has a 2-1/4" to 3-1/2" rolled edge tip by APC that is 8" long. Would that work? I think 4" may be a little too big at the end.

I initially went with 3 1/2 but they were to small, so go with at least 4 inch. Plus IMO the 8 inch length gives a nice appearance from the side.

go to my gallery and look for this pic and you will see how small they are.

 

[J DAWG]

my gallery is under J SMITH (username) or type in "3.5 inch tips" as the keyword.

 

[99 R/T 10]

I have a set of custom aluminum tips. Don't know if it is what your looking for, but thought I would give y'all a look. Bolt up to a 3" system and it opens to 4" at the exit.

 

[J DAWG]

found a pic of the 3 1/2.....way to small.....

You must be registered for see images

 

[J DAWG]

off topic- mike, how did you get your pic posted from the gallery here. For some reason I can't right click to copy and paste. Is that how you are posting them?


John

 

[Snake Bitten]

So said J DAWG

off topic- mike, how did you get your pic posted from the gallery here. For some reason I can't right click to copy and paste. Is that how you are posting them?


John

Like this???

 

[99 R/T 10]

Hey John,
right click on the thumb picture, copy the link. Then when you paste for an image, make sure to delete the "-thumb" part of the link.
Looks like G got it fixed up for ya

 

[J DAWG]

Hey John,
right click on the thumb picture, copy the link. Then when you paste for an image, make sure to delete the "-thumb" part of the link.
Looks like G got it fixed up for ya

Thanx Mike and G is just being a smart a$$ , but notice the 4 inchers he has on his car versus the 3 1/2 I had on mine.

 

[J DAWG]

just post *******