Before spending $1000 on a VEC 2, I would recommend spending $40-50 on 2 dyno pulls with A/F ratio plotted against RPM. My understanding (correct me if I'm wrong) is that stock and lightly modified cars benefit most with a VEC2 by adjusting the A/F ratio. Alteration of the spark advance is...
My son's are now 21 and 24. But when I first bought my viper in 1994 they were only 9 and 12. From the start they showed an interest in the car and enjoyed riding along. After they got their licenses I let them drive with me in the passenger seat. As they got more familiar with the car, I let...
I got the 3" stainless exhaust with the Borla muffler (without cat) for my '94 from Northwind Engineering. No more hot sills! It mates with the stock exhaust manifold so you can swap it out when it's time to smog. When I added Belanger headers, I had the stock cat/muffler modified so I can...
Northwind Engineering (see performance parts section) has a 2" lowering kit. The only caveat is that it fixes the seat in the rearmost position. I drive with the seat more toward the front so I went with their adjustable 1" kit
Thanks for the measurements. I am 6'2". While sitting on the floor against a wall, I measure 40" to the top of the helmet. Unless I recline the seatback, it looks like I'm stuck without a hardtop. Fortunately, I have the Autoform rollbar but it would be nice to have the insurance of the top if...
I would appreciate it if someone who owns an Autoform hardtop on their Gen 1 could post the height from the back of the driver's seat cushion to the inside of the top with the seat in the most forward position. Also mention whether you have a seat lowering kit. I emailed Autoform and all they...
Vipera:
You might want to check out West Coast Vipers in Murrieta, CA. www.westcoastvipers.com John Horton installed an autoform roll bar in my RT/10 and I was very happy with the install. I agree with Courtney that it is a very good investment if you are tracking your car. I was at Viper...
Re: Going to get dyno\'d tomorrow. What can I expect??
As you can see below, I have similar mods with the exception of Stage 2 heads from West Coast Viper and a new cam ( I believe it is a comp coupe) I chose a mild cam as I wanted driveablity on the street. The result was 510 RWHP/547 RWT
The R-hooks work great and are easy to use
http://www.awdirect.com/awdirect/catalog.cfm?dest=itempg&itemid=8978&secid=71&linkon=subsection&linkid=110
1. www.clearmask.com
2. I used 12 feet of the 6 inch wide tape
3. There are instructions with the tape.
4. I covered the front fenders behind the wheel, the side exhaust cover ( I have a 1994)to where the black paint starts ( i.e. until the exhaust cover straightens ), and the rear quarter...
Re: Chemists, Engineers, Dentists, and Flunkies like me look in here pleas
I suspect the addition of oxygen has nothing to do with generating N20 and in fact is to produce a N20 and oxygen mix. Nitrous oxide used for analgesia is not given at 100%. It needs to be mixed with oxygen ( for...
Re: Viper Days - Unlimited and
Chuck:
If you are talking about Michelin slicks, the only place I could find them was from Bobby Archer at http://www.bobbyarchermotorsports.com/. Tire Rack does carry the Kumho and Hoosier. I spoke with Skip Thomas at Viper Days and he clarified that you...
Perhaps this will help. It doesn't always have the part numbers for fastners but it should have the size so that you can purchase them at a hardware store
http://www.mopar.com/viper.html
I had the same thing happen to me when I had work done on my car. In my case the two electrical connections to the blower motor were disconnected. I don't know why they would have disconnected them to perform the service you discribed but its worth checking. As I recall, they are located just...
Has anyone refinished their Gen 1 dash? I can't find any information when I search the forums but presume someone must have done it by now. Mine is scratched and I was looking for suggestions on how to refinish it. Original appearance isn't a necessity.
The Vec 2 for the Gen 1 is definitely different. There is no inline connector. Everything needs to wired individually. I had West Coast Viper install and tune mine. It took 4 hours just for the installation. My understanding is that it's not particularly difficult, just time consuming. It...
Correct me if I'm wrong, but I believe the stock PCM controls the fuel and spark advance through an open loop system up to around 80% of WOT. It will "adapt" based on various outside parameters. Beyond 80% the fuel and spark advance are controlled by a closed loop system using fixed pre-set...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.