Search results

  1. J

    Making your own grills for the 08 hood??

    Well got the hood installed and it looks amazing...as if you all didn't know that already!! Bringing her home from the bodyshop and what pulls up next to me??...Gsxr 1k Third gear from about 75 to 115.... don't know if the guy was a wuss but I pulled on him by 2 car length!!:drive::drive::D:D...
  2. J

    Paxton dyno results........

    He did a few more runs after these and was able to get rid of the little dip in the mid-range hp.
  3. J

    Back from the tuner!!

    Well I got her back today and drove it about 300 miles down from up north. Unbelievable!!! I had a smile on my face for about 3 hours! I will post the dyno sheet when I get in the office on Monday. It made 700hp (dynojet) and 620ft/lb on a pretty conservative tune.
  4. J

    Paxton with little boost???

    So my tuner just called me and told that she is only putting out about 4.5lbs of boost. Stock pulley, marked the belt with only minimal slippage. WTF? He told me that with the improved exhaust flow(headers, pipes, no cats) that the stock pulley can't keep up. Any suggestions....I will most...
  5. J

    Quaife??? why

    So I am wondering why a lot of guys are really hyped on this rear-end? I understand it is a great diff. and for track purposes would be better, but for everyday wheel hop? isn't the stock diff. a limited slip? Whenever I can do a burnout (that is when the wheels aren't hopping off the car) it...
  6. J

    Radio question???

    Does anyone make a 2din bezel for the srt?
  7. J

    Does the Gen II AEM work for the Gen III?

    As stated in the title.
  8. J

    Anyone use these rotors?

    eBay Motors: Dodge Viper SRT-10 03-06 F&R Drill Slot Brake Rotors (item 320211005164 end time Feb-01-08 20:37:30 PST)
  9. J

    Good place to dyno tune??

    Looking for a good place to dyno tune my 05 Vert in or near Wisconsin.
  10. J

    Got my car back today!!

    Well I got my Viper back today and......................not sure yet. Under the hood looks pretty good. I will post pics in a day or so. Some of the fit and finish isn't great (hose wraps and such) but not bad at all. The side sills were mounted over my trim on the runner but Tony said they...
  11. J

    Asked why I bought it today.....

    I stop by the shop today to check on the progress for my Paxton install. They had it running and damn it sounds sweet with full billy boat exhaust......can't wait to hear it under a load! So I am just shooting the breeze with the mechanic and he stops and says : Why a Viper. Says I don't fit...
  12. J

    Is there a tire pressure sensor in the rim?

    Need to know this when I order. Thanks
  13. J

    Pulled the plug on the build!!

    So I am just laying around last night and I get a phone call from some guy saying he is sitting in my parking lot. (at my business) Tells me he found out I took my car to BIG3 performance and I was going to get screwed! I jumped in my truck and drove to the shop to meet him. He proceeds to...
  14. J

    Does the 8,3l have 4 bolt main caps?

    Looked around and can't find it
  15. J

    Viper in the SNOW!

    Off to the builder today so I had to drive her through the snow!:nono: She looks pretty though:drive:
  16. J

    Anyone powdercoat their intake?

    Looking to do a different look in the engine bay. I have a black vert which I am going to have HRE black rims installed. I want to do a black powdercoated intake with billet valve cover and the "Viper" lettering on the valve covers black. Should nice with polished fuel rails and the Paxton.
  17. J

    Vinyl strips???

    I deal with a company who does all my truck lettering and signs for my construction company. He told me he could do the strips on my Viper for cost. (Few hundred bucks) My company logo is black with silver and the silver looks awesome against the black. I will post pics when its done. If it...
  18. J

    Looking for Feedback: Spec Stage 5 clutch

    Is anyone running this clutch on there 800 to 1k hp car? Just looking to see how it's holding up and how "light switchy" it is when pulling out in first. Thanks in advance!
  19. J

    Build is on!!

    Here is the plan for my build: Paxton NOVI 2000 with 12lb pully Gatorback belt JE forged 9.0:1 pistons Eagle forged H-beam rods w/Clevite bearings Mopar Main bearings ARP head stubs Crower Billet custom ground cam Crower performance lifters Crower aluminum shaft mounted rocker arm kit...
  20. J

    Anyone with black rims on a black vert?

    Looking at a new set of rims for my black 05 and thinking about going with the HRE Comp 21's in black with crome lip. What do ya think?
  21. J

    Recalibration kit for SRT??

    Is it not needed? Hennessey Performance Engineering - Item Detail Page
  22. J

    Anyone with exp. in cryotreating.......

    I am wondering if it would be worth it to have the stock drive train cryotreated and if anyone has done this with success?
  23. J

    Would like advise on a build!

    Here is the story. I decided I wanted to build a high rwhp, hopefully around 1000rwhp srt daily driver. I know that there a few guys on this site that have great reps and could do the build no sweat. To the shugrin of most people on these forums I have decided to use a local builder. I do...
  24. J

    Powder coating stock rims??

    Has anyone tried this. I like the stock srt rims I just want them black.
  25. J

    Exhaust help PLEASE!!

    I realize there are a ton of these questions on this site but have searched and searched for weeks in trying to decide which exhaust system to go with. There are some sound clips here and there but still not much. I have a paxton with 3.55 gears and a stock exhaust. I have narrowed it down to...

Latest posts

Members online

Total: 887 (members: 15, guests: 872)

Forum statistics

Threads
153,218
Posts
1,682,068
Members
17,714
Latest member
potterb4

Share this page

Top